|
|
|
부품번호 | HCPL-2601 기능 |
|
|
기능 | HIGH SPEED-10 MBit/s LOGIC GATE OPTOCOUPLERS | ||
제조업체 | QT Optoelectronics | ||
로고 | |||
전체 10 페이지수
HIGH SPEED-10 MBit/s
LOGIC GATE OPTOCOUPLERS
SINGLE-CHANNEL
6N137
HCPL-2601
HCPL-2611
DESCRIPTION
The 6N137, HCPL-2601/2611 single-channel and HCPL-2630/2631 dual-channel
optocouplers consist of a 850 nm AlGaAS LED, optically coupled to a very high
speed integrated photodetector logic gate with a strobable output. This output
features an open collector, thereby permitting wired OR outputs. The coupled
parameters are guaranteed over the temperature range of -40°C to +85°C. A
maximum input signal of 5 mA will provide a minimum output sink current of 13
mA (fan out of 8).
An internal noise shield provides superior common mode rejection of typically 10
kV/µs. The HCPL- 2601 and HCPL- 2631 has a minimum CMR of 5 kV/µs.
The HCPL-2611 has a minimum CMR of 10 kV/µs.
8
FEATURES
• Very high speed-10 MBit/s
• Superior CMR-10 kV/µs
• Double working voltage-480V
• Fan-out of 8 over -40°C to +85°C
• Logic gate output
• Strobable output
• Wired OR-open collector
• U.L. recognized (File # E90700)
N/C 1
+2
V
F
_3
8
V
CC
7
V
E
6V
O
APPLICATIONS
• Ground loop elimination
• LSTTL to TTL, LSTTL or 5-volt CMOS
• Line receiver, data transmission
• Data multiplexing
• Switching power supplies
• Pulse transformer replacement
• Computer-peripheral interface
N/C 4
5 GND
Single-channel
circuit drawing
TRUTH TABLE
(Positive Logic)
Input
H
L
H
L
H
L
Enable
H
H
L
L
NC
NC
A 0.1 µF bypass capacitor must be connected between pins 8 and 5.
(See note 1)
DUAL-CHANNEL
HCPL-2630
HCPL-2631
8
1
8
1
1
+1
V
F1
_2
_3
V
F2
+4
8
V
CC
7
V
01
6V
02
5 GND
Dual-channel
circuit drawing
Output
L
H
H
H
L
H
8/10/99 200002A
HIGH SPEED-10 MBit/s
LOGIC GATE OPTOCOUPLERS
SINGLE-CHANNEL
6N137
HCPL-2601
HCPL-2611
DUAL-CHANNEL
HCPL-2630
HCPL-2631
TRANSFER CHARACTERISTICS (TA = -40°C to +85°C Unless otherwise specified.)
DC Characteristics
Test Conditions Symbol
Min
Typ**
High Level Output Current
Low Level Output Current
Input Threshold Current
(VCC = 5.5 V, VO = 5.5 V)
(IF = 250 µA, VE = 2.0 V) (Note 2)
(VCC = 5.5 V, IF = 5 mA)
(VE = 2.0 V, ICL = 13 mA) (Note 2)
(VCC = 5.5 V, VO = 0.6 V,
VE = 2.0 V, IOL = 13 mA)
IOH
VOL
IFT
.35
3
Max
100
.06
5
Unit
µA
V
mA
ISOLATION CHARACTERISTICS (TA = -40°C to +85°C Unless otherwise specified.)
Characteristics
Test Conditions Symbol
Min
Typ**
Max
Unit
Input-Output
(Relative humidity = 45%)
Insulation Leakage Current
(TA = 25°C, t = 5 s)
(VI-O = 3000 VDC)
(Note 12)
II-O
1.0* µA
Withstand Insulation Test Voltage
(RH < 50%, TA = 25°C)
(Note 12) ( t = 1 min.)
VISO
2500
VRMS
Resistance (Input to Output)
Capacitance (Input to Output)
(VI-O = 500 V) (Note 12)
(f = 1 MHz) (Note 12)
RI-O
CI-O
1012
0.6
!
pF
** All typical values are at VCC = 5 V, TA = 25°C
NOTES
1. The VCC supply to each optoisolator must be bypassed by a 0.1µF capacitor or larger. This can be either a ceramic or solid tantalum
capacitor with good high frequency characteristic and should be connected as close as possible to the package VCC and GND pins
of each device.
2. Each channel.
3. Enable Input - No pull up resistor required as the device has an internal pull up resistor.
4. tPLH - Propagation delay is measured from the 3.75 mA level on the HIGH to LOW transition of the input current pulse to the 1.5 V
level on the LOW to HIGH transition of the output voltage pulse.
5. tPHL - Propagation delay is measured from the 3.75 mA level on the LOW to HIGH transition of the input current pulse to the 1.5 V
level on the HIGH to LOW transition of the output voltage pulse.
6. tr - Rise time is measured from the 90% to the 10% levels on the LOW to HIGH transition of the output pulse.
7. tf - Fall time is measured from the 10% to the 90% levels on the HIGH to LOW transition of the output pulse.
8. tELH - Enable input propagation delay is measured from the 1.5 V level on the HIGH to LOW transition of the input voltage pulse
to the 1.5 V level on the LOW to HIGH transition of the output voltage pulse.
9. tEHL - Enable input propagation delay is measured from the 1.5 V level on the LOW to HIGH transition of the input voltage pulse
to the 1.5 V level on the HIGH to LOW transition of the output voltage pulse.
10. CMH - The maximum tolerable rate of rise of the common mode voltage to ensure the output will remain in the high state
(i.e., VOUT > 2.0 V). Measured in volts per microsecond (V/µs).
11. CML - The maximum tolerable rate of rise of the common mode voltage to ensure the output will remain in the low output state
(i.e., VOUT < 0.8 V). Measured in volts per microsecond (V/µs).
12. Device considered a two-terminal device: Pins 1,2,3 and 4 shorted together, and Pins 5,6,7 and 8 shorted together.
8/10/99 200002A
4페이지 Pulse
Generator
tr = 5ns
Z O = 50V !
1
Input
Monitor
(I F)
47 !
2
3
4
HIGH SPEED-10 MBit/s
LOGIC GATE OPTOCOUPLERS
SINGLE-CHANNEL
6N137
HCPL-2601
HCPL-2611
DUAL-CHANNEL
HCPL-2630
HCPL-2631
VCC 8
7 .1 %f
bypass
6
GND 5
+5V
RL
Output
(VO )
CL
Input
(I F)
tPHL
Output
(VO )
Output
(VO )
tf
I F = 7.5 mA
I F = 3.75 mA
tPLH
90%
10 %
1.5 V
tr
Fig. 12 Test Circuit and Waveforms for tPLH, tPHL, tr and tf.
Pulse
Generator
tr = 5ns
Z O = 50V !
1
7.5 mA
2
3
4
Input
Monitor
(VE)
+5V
VCC
8
7 .1 %f
bypass
6
5
GND
RL
Output
(VO )
CL
Input
(VE )
tEHL
Output
(VO )
3.0 V
1.5 V
tELH
1.5 V
Fig. 13 Test Circuit tEHL and tELH.
8/10/99 200002A
7페이지 | |||
구 성 | 총 10 페이지수 | ||
다운로드 | [ HCPL-2601.PDF 데이터시트 ] |
당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는 |
구매 문의 | 일반 IC 문의 : 샘플 및 소량 구매 ----------------------------------------------------------------------- IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한 광범위한 전력 반도체를 판매합니다. 전력 반도체 전문업체 상호 : 아이지 인터내셔날 사이트 방문 : [ 홈페이지 ] [ 블로그 1 ] [ 블로그 2 ] |
부품번호 | 상세설명 및 기능 | 제조사 |
HCPL-2601 | High Speed TTL Compatible Optocouplers | HP |
HCPL-2601 | HIGH SPEED-10 MBit/s LOGIC GATE OPTOCOUPLERS | Fairchild Semiconductor |
DataSheet.kr | 2020 | 연락처 | 링크모음 | 검색 | 사이트맵 |