Datasheet.kr   

HCPL-3180-300 데이터시트 PDF




Agilent(Hewlett-Packard)에서 제조한 전자 부품 HCPL-3180-300은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


 

PDF 형식의 HCPL-3180-300 자료 제공

부품번호 HCPL-3180-300 기능
기능 Current/ High Speed IGBT/MOSFET Gate Drive Optocoupler
제조업체 Agilent(Hewlett-Packard)
로고 Agilent(Hewlett-Packard) 로고


HCPL-3180-300 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 19 페이지수

미리보기를 사용할 수 없습니다

HCPL-3180-300 데이터시트, 핀배열, 회로
Agilent HCPL-3180 2 Amp Output
Current, High Speed IGBT/MOSFET Gate
Drive Optocoupler
Data Sheet
Description
This family of devices consists of
a GaAsP LED. The LED is
optically coupled to an
integrated circuit with a power
stage. These optocouplers are
ideally suited for high frequency
driving of power IGBT and
MOSFETs used in Plasma
Display Panels, high
performance DC/DC convertors
and motor control invertor
applications.
Ordering Information
Specify part number followed by
option number (if desired):
Example : HCPL-3180-XXX
N/C 1
ANODE 2
CATHODE 3
N/C 4
8 VCC
7 VO
6 VO
5 VEE
Functional Diagram
No option = Standard DIP
package, 50 per tube.
300 = Gull Wing Surface Mount
Option, 50 per tube.
500 = Tape and Reel Packaging
Option.
060 = DIN EN 60747-5-2 Option,
VIORM=630 Vpeak (pending
approval)
Features
2 A minimum peak output current
250 KHz maximum switching
speed
High speed response: 200 ns max
Propagation delay over
temperature range
10 KV/us minimum common mode
rejection (CMR) at VCM=1500 V
Under voltage lockout protection
(UVLO) with hysteresis
Wide operating temperature
range: -40 °C to +100 °C
Wide VCC operating range:
10 V to 20 V
20 ns typ pulse width distortion
Safety Approvals:
UL approval pending
3750 VRMS for 1 minute.
CSA approval
DIN EN 60747-5-2 approval
pending
Applications
Plasma Display Panel (PDP)
Distributed power architecture
(DPA)
Switch mode rectifier (SMR)
High performance DC/DC
convertor
High performance switch mode
power supply (SMPS)
High performance uninterruptible
power supply (UPS)
Isolated IGBT/Power MOSFET
gate drive
A 0.1 uF bypass capacitor must be connected between pins 5 and 8.
CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/
or degradation which may be induced by ESD.




HCPL-3180-300 pdf, 반도체, 판매, 대치품
DIN EN 60747-5-2 Insulation Characteristics (HCPL-3180 Option 060)
Description
Symbol
Installation classification per DIN EN 0110 1997-04
for rated mains voltage 150 Vrms
for rated mains voltage 300 Vrms
for rated mains voltage 600 Vrms
Climatic Classification
Pollution Degree (DIN EN 0110 1997 -04)
Maximum Working Insulation Voltage
VIORM
Input to Output Test Voltage, Method b*
VPR
VIORM x 1.875=VPR, 100% Production Test withtm=1 sec, Partial discharge < 5 pC
Input to Output Test Voltage, Method a*
VIORM x 1.5=VPR, Type and Sample Test, tm=60 sec,Partial discharge < 5 pC
VPR
Highest Allowable Overvoltage (Transient Overvoltage tini = 10 sec)
VIOTM
Safety-limiting values - maximum values allowed in the event of a failure.
Case Temperature
Input Current**
Output Power**
Insulation Resistance at TS, VIO = 500 V
TS
IS, INPUT
PS, OUTPUT
RS
HCPL-3180
I - IV
I - III
I - II
55/100/21
2
630
1181
945
6000
175
230
600
>109
Unit
Vpeak
Vpeak
Vpeak
Vpeak
°C
mA
mW
W
* Refer to the optocoupler section of the Isolation and Control Components Designer’s Catalog, under Product Safety Regulations section, (DIN) for a
detailed description of Method A and Method B partial discharge test profiles.
** Refer to the following figure for dependence of PS and IS on ambient temperature.
800
700
PS (mW)
IS (mA)
600
500
400
300
200
100
0
0 25 50 75 100 125 150 175 200
T S – CASE TEMPERATURE – ˚C
4

4페이지










HCPL-3180-300 전자부품, 판매, 대치품
Switching Specifications (AC)
Over recommended operating conditions unless otherwise specified.
Parameter
Propagation Delay Time to High Output Level
Symbol
tPLH
Min Typ
50 150
Propagation Delay Time to Low Output Level
tPHL
50 150
Pulse Width Distortion
Propagation Delay Difference Between Any Two
Parts
Rise Time
Fall Time
UVLO Turn On Delay
UVLO Turn Off Delay
Output High Level Common Mode Transient
Immunity
PWD
PDD
(tPHL - tPLH)
tr
-90
tf
tUVLO ON
tUVLO OFF
|CMH|
10
20
25
25
2.0
0.3
Output Low Level Common Mode Transient
Immunity
|CML|
10
Max
200
200
65
90
Units Test Conditions Fig Note
ns IF = 10 mA
Rg = 10 W
f = 250 kHz
10, 16
11,
12,
ns
Duty Cycle = 50%
Cg = 10 nF
13,
14,
23
ns 12
ms 35, 17
36
ns CL = 1 nF
Rg = 0 W
ns
23
us 22
us
kV/µs
kV/µs
TA = +25 °C
If = 10 to 16 mA
VCM = 1.5 kV
VCC = 20 V
TA = +25 °C
Vf = 0 V
VCM = 1.5 kV
VCC = 20 V
VCM = 1.5 kV
24 13, 14
13, 15
Package Characteristics
Parameter
Input-Output Momentary Withstand Voltage
Input-Output Resistance
Input-Output Capacitance
Symbol
VISO
RI-O
CI-O
Min Typ Max Units Test Conditions Fig Note
2500
Vrms TA = +25 °C,
RH < 50%
8, 9
1011
W VI-O = 500 V
1 pF Freq = 1 MHz
9
Notes:
1. Derate linearly above +70 °C free air temperature at a rate of 0.3 mA/°C.
2. Maximum pulse width = 10 us, maximum duty cycle = 0.2%. This value is intended to allow for component tolerances for designs with IO peak
minimum = 2.0 A. See Application section for additional details on limiting IOL peak.
3. Derate linearly above +70 °C, free air temperature at the rate of 4.8 mW/°C.
4. Derate linearly above +70 °C, free air temperature at the rate of 5.4 mW/°C. The maximum LED junction temperature should not exceed +125 °C.
5. Maximum pulse width = 50 us, maximum duty cycle = 0.5%.
6. In this test, VOH is measured with a dc load current. When driving capacitive load VOH will approach VCC as IOH approaches zero amps.
7. Maximum pulse width = 1 ms, maximum duty cycle = 20%.
8. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage > 3000 Vrms for 1 second (leakage detection
current limit II-O < 5 uA).
9. Device considered a two-terminal device: pins on input side shorted together and pins on output side shorted together.
10. tPHL propagation delay is measured from the 50% level on the falling edge of the input pulse to the 50% level of the falling edge of the VO signal. tPLH
propagation delay is measured from the 50% level on the rising edge of the input pulse to the 50% level of the rising edge of the VO signal
11. tPSK is equal to the magnitude of the worst case difference in tPHL and/or tPLH that will be seen between units at any given temperature within the
recommended operating conditions
12. PWD is defined as |tPHL - tPLH | for any given device.
13. Pin 1 and 4 need to be connected to LED common.
7

7페이지


구       성 총 19 페이지수
다운로드[ HCPL-3180-300.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
HCPL-3180-300

Current/ High Speed IGBT/MOSFET Gate Drive Optocoupler

Agilent(Hewlett-Packard)
Agilent(Hewlett-Packard)

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵