|
|
Número de pieza | LA75676VA | |
Descripción | IF Signal Processor | |
Fabricantes | Sanyo | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de LA75676VA (archivo pdf) en la parte inferior de esta página. Total 10 Páginas | ||
No Preview Available ! Ordering number : EN7868
LA75676VA
Monolithic Linear IC
IF Signal Processor (VIF+SIF)
for TV and VCR Products
Overview
The LA75676VA is a VIF/SIF IC that supports NTSC intercarrier reception and adopts a semi-adjustment-free design. It is
provided in the SSOP24 (225mil, 0.5mm lead pitch) package, which is appropriate for miniature 2-in-1 tuner products. In
the VIF block, it adopts a design that uses AFT adjustment to obviate the need for VCO adjustment, and thus can simplify
the adjustment steps required in end product manufacturing. It uses a PLL technique for FM detection. It features the 5V
supply voltage appropriate for multimedia products. In addition, it achieves superb audio quality by incorporating a buzz
canceller that suppresses Nyquist buzzing.
Functions
• VIF block: VIF amplifier, buzz canceller, PLL detector, IF AGC, RF AGC, AFT, and an equalizer amplifier
• SIF block: Limiter amplifier, PLL FM detector
Specifications
Maximum Ratings at Ta = 25°C
Parameter
Maximum supply voltage
Circuit voltage
Circuit current
Allowable power dissipation
Operating temperature
Storage temperature
Symbol
VCC max
V13, V17
I6
I10
I24
Pd max
Topr
Tstg
Conditions
Ta ≤ 70°C * Mounted on a board
* When mounted on a 114.3×76.1×1.6mm3 glass epoxy board.
Operating Conditions at Ta = 25°C
Parameter
Recommended supply voltage
Operating supply voltage range
Symbol
VCC
VCC op
Conditions
Ratings
6
VCC
-3
-10
-2
600
-20 to +70
-55 to +150
Unit
V
V
mA
mA
mA
mW
°C
°C
Ratings
5
4.5 to 5.5
Unit
V
V
Any and all SANYO Semiconductor products described or contained herein do not have specifications
that can handle applications that require extremely high levels of reliability, such as life-support systems,
aircraft's control systems, or other applications whose failure can be reasonably expected to result in
serious physical and/or material damage. Consult with your SANYO Semiconductor representative
nearest you before using any SANYO Semiconductor products described or contained herein in such
applications.
SANYO Semiconductor assumes no responsibility for equipment failures that result from using products
at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition
ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor
products described or contained herein.
Downloaded from Elcodis.com electronic components distributor
N1506 MS PC B8-6591, B8-6996 No.7868-1/10
1 page LA75676VA
Test Conditions
V1. Circuit current • • • • [15]
1. Internal AGC
2. Input a 45.75MHz, 10mVrms, CW signal to the VIF input pin.
3. RF AGC Vr maximum
4. Connect a current meter to VCC and measure the current flowing into the IC.
V2, V3. Maximum RF AGC voltage, minimum RF AGC voltage • • • • [V9H, V9L]
1. Internal AGC
2. Input a 45.75MHz, 10mVrms, CW signal to the VIF input pin.
3. Vary the RF AGC Vr and, at the maximum resistance, measure the maximum RF AGC voltage. (F)
4. Vary the RF AGC Vr and, at the minimum resistance, measure the maximum RF AGC voltage. (F)
V4. Input sensitivity • • • • [Vi]
1. Internal AGC
2. fp = 45.75MHz, 400Hz 40% AM (VIF input)
3. Set S1 to the off position and pass the input through a 100kΩ resistor.
4. Measure the VIF input level such that the 400Hz detection output level at test point A becomes 0.64Vp-p.
V5. AGC range • • • • [GR]
1. External AGC. Apply the VCC voltage to the IF AGC input (pin 17).
2. With the same conditions as used for V4, measure the VIF input level such that the detection output level becomes
0.64Vp-p. • • • Vi1
Vi1
3. GR = 20log Vi dB
V6. Maximum allowable input • • • • [Vi max]
1. Internal AGC
2. fp = 45.75MHz, 15kHz 78% AM (VIF input)
3. Measure the VIF input level such that the detection output level at test point A is ±1dB of the video output (Vo).
V7. Video output voltage (no input) • • • • [V6]
1. External AGC. Apply the VCC voltage to the IF AGC input (pin 17).
2. Measure the video output (A) DC voltage.
V8. Sync signal tip voltage • • • • [V6tip]
1. Internal AGC
2. Input a 45.75MHz, 10mVrms, CW signal to the VIF input pin.
3. Measure the video output (A) DC voltage.
V9. Video output level • • • • [Vo]
1. Internal AGC
2. fp = 45.75MHz, 15kHz 78% AM
Vi = 10mVrms (VIF input)
3. Measure the wave height of the detection output level at test point A. (Vp-p)
Downloaded from Elcodis.com electronic components distributor
No.7868-5/10
5 Page |
Páginas | Total 10 Páginas | |
PDF Descargar | [ Datasheet LA75676VA.PDF ] |
Número de pieza | Descripción | Fabricantes |
LA75676V | IF Signal Processor (VIFSIF) | Sanyo Semicon Device |
LA75676V-S | VIF/SIF IF Signal-Processing Circuit for TV and VCR Products | Sanyo |
LA75676VA | IF Signal Processor | Sanyo |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |