Datasheet.kr   

HB288800A6 데이터시트 PDF




Hitachi Semiconductor에서 제조한 전자 부품 HB288800A6은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


 

PDF 형식의 HB288800A6 자료 제공

부품번호 HB288800A6 기능
기능 FLASH ATA Card
제조업체 Hitachi Semiconductor
로고 Hitachi Semiconductor 로고


HB288800A6 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.



전체 30 페이지수

미리보기를 사용할 수 없습니다

HB288800A6 데이터시트, 핀배열, 회로
HB2881000A6/HB288800A6
HB288640A6/HB288448A6
HB288320A6/HB288256A6
HB288192A6/HB288160A6
HB288128A6/HB288096A6
HB288064A6/HB288032A6
FLASH ATA Card
1 GByte/800 MByte/640 MByte/448 MByte/320 MByte
256 MByte/192 MByte/160 MByte/128 MByte
96 MByte/64 MByte/32 MByte
ADE-203-1177A (Z)
Rev. 1.0
Dec. 8, 2000
Description
HB2881000A6, HB288800A6, HB288640A6, HB288448A6, HB288320A6, HB288256A6, HB288192A6,
HB288160A6, HB288128A6, HB288096A6, HB288064A6, HB288032A6 are Flash ATA card. This card
complies with PC card ATA standard and is suitable for the usage of data storage memory medium for PC or
any other electric equipment. This card is equipped with Hitachi 256 Mega bit Flash memory. This card is
suitable for ISA (Industry Standard Architecture) bus interface standard , and read/write unit is 1 sector (512
bytes) sequential access. By using this card it is possible to operate good performance for the system which
have PC card slots.
Features
PC card ATA standard specification
68 pin two pieces connector and Type II (5 mm)
3.3 V/5 V single power supply operation
ISA standard and Read/Write unit is 512 bytes (sector) sequential access
Sector Read/Write transfer rate: 8MB/sec burst




HB288800A6 pdf, 반도체, 판매, 대치품
HB2881000/800/640/448/320/256/192/160/128/096/064/032A6
Pin No.
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
Memory card mode
Signal name I/O
GND
GND
-CD1
O
D11 I/O
D12 I/O
D13 I/O
D14 I/O
D15 I/O
-CE2
I
-VS1
O
-IORD
I
-IOWR
I
——
——
——
——
——
VCC
——
——
——
——
-CSEL
I
-VS2
O
RESET
I
-WAIT
O
-INPACK
O
-REG
I
BVD2
I/O
BVD1
I/O
D8 I/O
D9 I/O
D10 I/O
-CD2
O
GND
I/O card mode
Signal name
GND
GND
-CD1
D11
D12
D13
D14
D15
-CE2
-VS1
-IORD
-IOWR
VCC
-CSEL
-VS2
RESET
-WAIT
-INPACK
-REG
-SPKR
-STSCHG
D8
D9
D10
-CD2
GND
I/O
O
I/O
I/O
I/O
I/O
I/O
I
O
I
I
I
O
I
O
O
I
I/O
I/O
I/O
I/O
I/O
O
True IDE mode
Signal name
GND
GND
-CD1
D11
D12
D13
D14
D15
-CE2
-VS1
-IORD
-IOWR
VCC
-CSEL
-VS2
-RESET
IORDY
-INPACK
-REG
-DASP
-PDIAG
D8
D9
D10
-CD2
GND
I/O
O
I/O
I/O
I/O
I/O
I/O
I
O
I
I
I
O
I
O
O
I
I/O
I/O
I/O
I/O
I/O
O
4

4페이지










HB288800A6 전자부품, 판매, 대치품
HB2881000/800/640/448/320/256/192/160/128/096/064/032A6
Signal name
Direction Pin No.
-IOWR
I
(PC Card Memory mode)
45
-IOWR
(PC Card I/O mode)
-IOWR
(True IDE mode)
-OE I
(PC Card Memory mode)
-OE
(PC Card I/O mode)
-ATASEL
(True IDE mode)
RDY/-BSY
O
(PC Card Memory mode)
9
16
-IREQ
(PC Card I/O mode)
INTRQ
(True IDE mode)
-REG
I
(PC Card Memory mode)
Attribute memory select
-REG
(PC Card I/O mode)
-REG
(True IDE mode)
61
Description
This signal is not used.
-IOWR is used for control of data write in I/O task file
area. This card does not respond to -IOWR until I/O
card interface setting up.
-IOWR is used for control of data write in I/O task file
area. This card does not respond to -IOWR until True
IDE interface setting up.
-OE is used for the control of reading register’s data in
attribute area or task file area.
-OE is used for the control of reading register’s data in
attribute area.
To enable True IDE mode this input should be
grounded by the host.
The signal is RDY/-BSY pin. RDY/-BSY pin turns low
level during the card internal initialization operation at
VCC applied or reset applied, so next access to the
card should be after the signal turned high level.
This signal is active low -IREQ pin. The signal of low
level indicates that the card is requesting software
service to host, and high level indicates that the card
is not requesting.
This signal is the active high Interrupt Request to the
host.
-REG is used during memory cycles to distinguish
between task file and attribute memory accesses.
High for task file, Low for attribute memory is
accessed.
-REG is constantly low when task file or attribute
memory is accessed.
This input signal is not used and should be connected
to VCC.
7

7페이지


구       성 총 30 페이지수
다운로드[ HB288800A6.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
HB288800A5

FLASH ATA Card

Hitachi Semiconductor
Hitachi Semiconductor
HB288800A6

FLASH ATA Card

Hitachi Semiconductor
Hitachi Semiconductor

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵