ACE4722 Datasheet PDF - ACE Technology
| Part Number | ACE4722 | |
| Description | Multi-Chemistry Battery Charger IC | |
| Manufacturers | ACE Technology | |
| Logo |  |
|
|
There is a preview and ACE4722 download ( pdf file ) link at the bottom of this page. Total 14 Pages | ||
Preview 1 page No Preview Available !
ACE4722
5A, Multi-Chemistry Battery Charger IC With Photovoltaic Cell MPPT Function
Description
The ACE4722(Note 1) is a PWM switch-mode battery charger controller that can be powered by
photovoltaic cell with maximum power point tracking function. The ACE4722 is specially designed for
charging 1 or multi-cell lithium ion batteries or LiFePO4 batteries with constant current and constant
voltage mode. In constant voltage mode, the regulation voltage is set by the external resistor divider. The
constant charging current is programmable with a single current sense resistor.
Deeply discharged batteries are automatically trickle charged at 15% of the programmed constant
charging current until the cell voltage exceeds 66.7% of the regulation voltage. In constant voltage mode,
the charging current decreases gradually, the charge cycle will be terminated when the charging current
drops to 9.5% of the full-scale current, and a new charge cycle automatically restarts if the battery voltage
falls below 95.8% of the regulation voltage in constant voltage mode.
ACE4722 will automatically enter sleep mode when input voltage is lower than battery voltage. Other
features include undervoltage lockout, battery temperature monitoring and status indication, etc.
Features
Photovoltaic Cell Maximum Power Point Tracking
Wide Input Voltage: 7.5V to 28V
Complete Charger Controller for 1 or multi-cell Lithium-ion Battery or LiFePO4 Battery
Charge Current Up to 5A
High PWM Switching Frequency: 300KHz
Constant Charging Voltage Set By the External Resistor Divider
Charging Current is programmed with a sense resistor
Automatic Conditioning of Deeply Discharged Batteries
Battery Temperature Monitoring
2 Status Indications
Soft Start
Battery Overvoltage Protection
Operating Ambient Temperature -40℃ to ＋85℃
Application
The Charger Powered by Photovotaic cell
Electric Tools
Battery-Backup Systems
Standalone Battery Chargers
Note 1: Patent Pending
VER 1.2 1
|
| |
 
ACE4722
5A, Multi-Chemistry Battery Charger IC With Photovoltaic Cell MPPT Function
DONE Sink Current
DONE Leakage Current
IDONE
ILK2
DONE Pin
VDONE=1V, termination
mode
VDON=25V, charge mode
Oscillator
Switching Frequency
fosc
Maximum Duty Cycle
Dmax
Sleep Mode
Sleep Mode Threshold
(measure VCC-VBAT)
Sleep mode Release Threshold
(measure VCC-VBAT)
VSLP
VSLPR
VCC falling
VCC rising
DRV Pin
VBAT=8V
VBAT=12V
VBAT=18V
VBAT=8V
VBAT=12V
VBAT=18V
VDRV High (VCC-VDRV)
VDRV Low (VCC-VDRV)
Rise Time
Fall Time
VH IDRV=-10mA
VL IDRV=0mA
tr Cload=2nF, 10% to 90%
tf Cload=2nF, 90% to 10%
Note 2: VREG is the regulation voltage at BAT pin in constant voltage mode
7
240
0.06
0.1
0.18
0.26
0.32
0.38
5
30
30
12
300
94
0.1
0.14
0.23
0.32
0.42
0.47
60
6.5
40
40
18
1
360
0.14
0.18
0.28
0.39
0.52
0.58
8
65
65
mA
uA
kHZ
%
V
V
mV
V
ns
ns
Detailed Description
The ACE4722 is a constant current, constant voltage battery charger controller that can be powered by
the photovoltaic cell with maximum power point tracking function, the device is specially designed for 1 or
multi-cell Li-Ion battery or LiFePO4 batteries. The charge current is set by an external sense resistor
(RCS) across the CSP and BAT pins. The final battery regulation voltage VREG in constant voltage mode is
set by the external resistor divider.
A charge cycle begins when the following 3 conditions are met:
(1) The voltage at VCC pin rises above the UVLO level
(2) The voltage at VCC pin is greater than the battery voltage by sleep mode release threshold VSLPR
(3) The voltage at VCC pin is no less than the maximum power point voltage set by the external resistors
At the beginning of the charge cycle, if the battery voltage is less than 66.7%*VREG, the charger goes into
trickle charge mode. The trickle charge current is internally set to 15%(Typical) of the full-scale current.
When the battery voltage exceeds 66.7%*VREG, the charger goes into the full-scale constant current
charge mode. In constant current mode, the charge current is set by the external sense resistor RCS and
an internal 200mV reference, so the charge current equals to 200mV/RCS. When the battery voltage
approaches the regulation voltage, the charger goes into constant voltage mode, and the charge current
will start to decrease. In constant voltage mode, the charge cycle will be terminated once the charge
current decreases to 9.5% of the full-scale current. During the charge termination status, the DRV pin is
pulled up to VCC, and an internal comparator turns off the internal pull-down N-channel MOSFET at the
pin, another internal pull-down N-channel MOSFET at the pin is turned on to indicate the termination
status.
VER 1.2 5
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for ACE4722 electronic component. |
| Information | Total 14 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ ACE4722.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| ACE4722 | The function is Multi-Chemistry Battery Charger IC. ACE Technology | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
ACE4
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||