|
|
PDF SVX-1920 Data sheet ( Hoja de datos )
| Número de pieza | SVX-1920 | |
| Descripción | INTERFACE CONTROLLER | |
| Fabricantes | Digital View | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de SVX-1920 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
PC, DVI, HDMI, VIDEO INTERFACE CONTROLLER
FOR TFT PANEL
Model: SVX-1920
Part number : 41721003X-3 or up
[Firmware version : V0.45.00.01 or up]
INSTRUCTIONS
CONTENTS
Page: 2. Introduction, How to Proceed, Usage Note, Disclaimer
3. System design – Diagram of a suggested system
4. Assembly notes – Important information about system elements
7. Connection & Operation – How to use the controller
14. Connectors, pinouts & jumpers – Essential connection information
26. Controller dimensions
27. Application notes
29. Troubleshooting
30. Specifications
31. Appendix I – Supported graphics modes table
34. Appendix II – RS-232 control protocols
51. Appendix III – Mapping definition
55. Appendix IV – Auto Color Gain
56. Appendix V – DV remote control unit work for SVX-1920
57. Appendix VI – Function description for de-interlacing mode AFM, TNR,
MADI, DCDi
57. Appendix VII – PIP mix table
59. Appendix VIII - Network connection
60. Appendix IX – RM-DN5 Assembly connection
61. Appendix X – Specification for inverter Interface Board P/N 416040010-3
64. Appendix XI - Specification for audio add-on board P/N 416940020-3
66. Warranty, Caution & Limitation of Liability, Trademarks
67.Contact details
It is essential that these instructions are read and understood before connecting or
powering up this controller.
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 2.2: 12 Dec, 2011 (SVX-1920_manual.doc)
Page 1 of 67
1 page  
12. External panel power output : User for specific panel model.
13. Panel control signal : Use for specific panel model.
14. Audio add-on board P/N 416940020-3: Provide the interface for the audio add-on board P/N 416940020-3 to be
connected. The audio add-on board gives the audio input and output signal connection. The volume can be controlled by
the OSD menu on the controller. It is an optional part only, can be unconnected if not using audio.
CAUTION : The Audio Add-on Board P/N 416940020-3 is only operate under 12VDC power input environment.
15. Auxiliary +5VDC output : 2 ways connector provides +5VDC output.
16. Ambient light sensor connection : 3 ways connector provides interface for ambient light sensor connection by using Kit
70220-3.
17. Backlight status input : 2 ways connector provides interface for connection with the specific panel type which support the
panel with backlight status monitoring function.
18. HD / SD Component video input : Plug the component video input cable P/N 426000600-3 on CNV2 connector
19. Composite & S-video input : Standard Composite cables can be used. Reasonable quality cable should be used to avoid
image quality degradation.
20. HDMI audio output : Support HDMI audio with stereo output.
The HDMI audio output can be connected to Audio add-on board P/N 416940020-3 by using the audio cable P/N
426451800-3 (310mm) connected between SVX-1920 (connector : CN10) and Audio add-on board P/N 416940020-3
(connector : CN2).
21. Alternate HDMI input : This port gives alternate HDMI input support. This port is not support when P3 connector is
connected.
22. Alternate DVI input : This port gives alternate DVI input support. This port is not supported when P2 connector is
connected.
23. Reserved : No function, reserved for future development.
24. SPDIF Audio output : This port support SPDIF audio output from the HDMI audio source inputted.
25. DVI-D input cable : Plug the DVI cable to the connector P3 on the controller board.
26. HDMI input : Plug the HDMI cable to the connector P2 on the controller board. This port is not supported when CN5 is
connected.
27. Analog RGB Input : As this may affect regulatory emission test results and the quality of the signal to the controller a
suitably shielded cable should be utilized.
28. Control over network connection : This is a network device that allow to control RS-232 enable devices over a TCP/IP
based Ethernet and the Internet using a web browser. Please refer to Appendix VIII in details.
29. Auxiliary video input : This port provides Composite video 1 & 2, S-video 1 & 2, Component 1 & 2. The video input
selection can be switched via RS-232 command (0x98) or OSD menu.
30. Power Input: 12V/24VDC is required, this should be a regulated supply. The power rating is depending on the panel and
inverter used. Normally, power supply with 3.5Amp current output should enough for most of 4x CCFT panels. Although
the controller provides power regulation for the LCD power this does not relate to the power supplied to the backlight
inverter. If an unregulated power supply is provided to an inverter any fluctuations in power may affect operation,
performance and lifetime of the inverter and or backlight tubes.
31. External panel power input : Allow to supply external power to the panel separately for max 3.3V (7A) or 5V (7A) or 12V
(5A) or 18V (3.5A) via PP4 power input connector. Corresponding jumper setting of JA3, JA5 & JA6 are required for each
panel power input by referring to page 17.
• Power output: Note the controller has an overall 3Amp current limit and the current available from the auxiliary power
output will be dependent on the power input and other system requirements.
• Power Safety: Note that although only 12V / 24VDC is required as ‘power-in’ a backlight inverter for panel backlighting
produces significantly higher voltages (the inverter does not connect to the ground plane). We strongly advise appropriate
insulation for all circuitry.
• EMI: Shielding will be required for passing certain regulatory emissions tests. Also the choice of external Controller to PC
signal cable can affect the result.
• Ground: The various PCB mounting holes are connected to the ground plane.
• Servicing: The board is not user serviceable or repairable. Warranty does not cover user error in connecting up to the
controller and is invalidated by unauthorized modification or repairs.
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 2.2: 12 Dec, 2011 (SVX-1920_manual.doc)
Page 5 of 67
5 Page 
Composite 1
Composite 2
S-Video 1
S-Video 2
Component 1
Component 2
The corresponding input port name display on OSD menu will disappear once
setting “OFF”.
Auto Power :
OFF / ON
ON – Enable soft power off function if absence of input signals
OFF – Disable soft power function
De-interlacing Mode* 4
AFM
: Auto Film Mode
TNR
: Temporal Noise Reduction
MADI
: Motion Adaptive De-interlacing
DCDi
: Low Angled De-interlacing
[See Appendix VI for AFM, TNR, MADI, DCDi function description]
Video Wall Setup 4
Video Wall
Video Wall Size : Choose the video wall size (Number of panel for horizontal [max
4] x Number of panel for vertical [max 4]).
Video Wall ID Setup : Set the matching ID number same as the ID number shown
on screen. For details, please refer to the application note
of the video wall setup.
Bezel Compensation 4
Bezel Compensation
Active Area (H) (mm) : Type in the active area in horizontal with reference to the
panel specification
Active Area (V) (mm) : Type in the active area in vertical with reference to the panel
specification
Bezel Opening Area (H) (mm) : Type in the bezel opening area in horizontal with
reference to the panel specification.
Bezel Opening Area (V) (mm) : Type in the bezel opening area in vertical with
reference to the panel specification.
Enable RGB SOG:
OFF / ON
Video Standard (SD)* : Auto / NTSC / NTSC 4.43 / PAL / PAL M / SECAM
Gamma : 0.6 / 0.7/ 0.8 / 1.0 / 1.6 / 1.8 / 1.9 / 2.0 / 2.1 / 2.2 / 2.3 / 2.4 / 2.5 / 2.6 / User Setting
OSD 4
OSD position :
H POS
: Move the OSD menu image horizontally
V POS
: Move the OSD menu image vertically
OSD Timeout (sec) : ON – 60 : Adjust the OSD menu timeout period in a step of 5
seconds (max 60 seconds)
ON = Continuous to display OSD menu.
60 = 60 seconds later will turn off the OSD menu.
Screen Marker 4
Screen Marker : On/Off
Center Marker : On/Off
Safe Area Enable : On/ Off
Aspect Marker Enable : On/Off
Safe Area Market : 80%~99%
Aspect Marker : 4:3 / 16:9
Transparency Level : 0% / 25% / 50% / 75% / 100%
Exit menu
Language : English / Spanish / French / German / Chinese :Select OSD menu language display
Transparency :
OFF / ON : Set OSD transparency
Display Input :
OFF / ON : Display input source info after switching source.
Real time clock 4 show and edit the real time clock (This function is valid when “Display Input”
sets ON.)
DATE : DD/MM/YYYY : Date/Month/Year
TIME : HH/MM/SS (AM/PM): Hour/Minute/Second
SETUP 4
Month / Day / Year
Hour / Minute / AM/PM
Display Clock
: Disable or enable to display the real time clock when
display video source info after switching source.
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 2.2: 12 Dec, 2011 (SVX-1920_manual.doc)
Page 11 of 67
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet SVX-1920.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| SVX-1920 | INTERFACE CONTROLLER | Digital View |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |