Datasheet.kr   

PCJ1A680MCL1GS 데이터시트 PDF




Nichicon에서 제조한 전자 부품 PCJ1A680MCL1GS은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


PDF 형식의 PCJ1A680MCL1GS 자료 제공

부품번호 PCJ1A680MCL1GS 기능
기능 CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
제조업체 Nichicon
로고 Nichicon 로고


PCJ1A680MCL1GS 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 2 페이지수

미리보기를 사용할 수 없습니다

PCJ1A680MCL1GS 데이터시트, 핀배열, 회로
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CJ Chip Type, Low ESR,
Higher Capacitance
series
CK
Low ESR, Higher Capacitance, High ripple current.
Load life of 2000 hours at 105°C.
SMD type : Lead free reflow soldering condition at
260°C peak correspondence.
Compliant to the RoHS directive (2002/95/EC).
Low ESR
CJ
Specifications
Low ESR
Higher
Capacitance,
CF
Item
Performance Characteristics
Category Temperature Range 55 to +105°C
Rated Voltage Range
2.5 to 16V
Rated Capacitance Range 33 to 2700µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C
ESR ( 1)
Less than or equal to the specified value at 100kHz, 20°C
Leakage Current ( 2) Less than or equal to the specified value . After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+105°C / Z+20°C 1.25
Z55°C / Z+20°C 1.25
(100kHz)
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours at 105°C.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Damp Heat
(Steady State)
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Resistance to
Soldering Heat
Marking
After soldering the capacitor under the soldering conditions
prescribed here, the capacitor shall meet the specifications listed at
right, provided that it's temperature profile is measured at the
capacitor top and the terminal.
Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec.
The duration for over +230°C temperature at capacitor surface shall
not exceed 60 seconds.
In the case of peak temp, less than 250°C, reflow soldering shall be
two times maximum.
In the case of peak temp, less than 260°C, reflow soldering shall be
once.
Measurement for solder temperature profile shall be made at the
capacitor top and the terminal.
Navy blue print on the case top
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Capacitance
Lot No.
Plastic platform
0.3 MAX.
C±0.2
Positive
Series
Voltage ( j:6.3v)
L
+0.1
- 0.4
Negative
H
Type numbering system (Example : 6.3V 220µF)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
PC J 0 J 2 2 1 MC L 1 GS
Taping code
Size code
Configuration
Capacitance toleranc (±20%)
Rated capacitance (220µF)
Rated voltage (6.3V)
Series name
Type
(mm)
Size φ5 × 6L φ6.3 × 6L φ6.3 × 8L φ8 × 7L φ8 × 8L φ8 × 10L φ8 × 12L φ10 × 8L φ10 × 10L φ10 × 12.7L
φD 5.0 6.3 6.3 8.0 8.0 8.0 8.0 10.0 10.0 10.0
L 5.9 5.9 7.9 6.9 7.9 9.9 11.9 7.9 9.9 12.6
A 6.0 7.3 7.3 9.0 9.0 9.0 9.0 11.0 11.0 11.0
B 5.3 6.6 6.6 8.3 8.3 8.3 8.3 10.3 10.3 10.3 Voltage
C 5.3 6.6 6.6 8.3 8.3 8.3 8.3 10.3 10.3 10.3
E 1.6 2.1 2.1 3.2 3.2 3.2 3.2 4.6 4.6 4.6
H 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1
V 2.5 4 6.3 10 16
Code e g j A C
Dimension table in next page.
CAT.8100Z





구       성 총 2 페이지수
다운로드[ PCJ1A680MCL1GS.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
PCJ1A680MCL1GS

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS

Nichicon
Nichicon

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵