Datasheet.kr   

ELIS-1024A-LG PDF 데이터시트 : 부품 기능 및 핀배열

부품번호 ELIS-1024A-LG
기능 High Performance Linear Image Sensors
제조업체 Panavision Imaging
로고 Panavision Imaging 로고 



전체 13 페이지

		

No Preview Available !

ELIS-1024A-LG 데이터시트, 핀배열, 회로
ONE TE C H N O L O G Y PLACE – HOMER, NEW YORK 13077
TEL: +1 607 749 2000 FAX: +1 607 749 3295 www.PanavisionImaging.com / sales@PanavisionImaging.com
High Performance Linear Image Sensors
ELIS-1024 IMAGER
The Panavision Imaging ELIS is a high performance linear image sensor designed to replace CCD’s in a wide
variety of applications, including:
Edge Detection
Contact Imaging
Bar Code Reading
Finger Printing
Encoding and Positioning
Text Scanning
P/N: ELIS-1024A-LG
16-pin LCC package
P/N: ELIS-1024A-D-ES
16-pin ceramic DIP package
P/N: ELIS-1024A-CP-ES
CSP package (µBGA)
Description
The ELIS-1024 Linear Image Sensor consists of an array of high performance, low dark current photo-diode
pixels. The sensor features sample and hold capability, selectable resolution and advanced power
management. The device can operate at voltages as low as 2.8V making it ideal for portable applications. A
key feature over traditional CCD technology is that the device can be read and reread Non-Destructively,
allowing the user to maximize signal to noise and dynamic range. Internal logic automatically reduces power
consumption when lower resolution settings are selected. A low power standby mode is also available to
reduce system power consumption when the imager is not in use. Available in a low cost SMT package as
well as a high performance dual inline ceramic package.
Key Features
Low Cost
Single Voltage Operation, Wide Operating Range
Selectable Resolutions of 1024, 512, 256 and 128 pixels
Intelligent Power Management and Low-Power Standby Mode
Sample and Hold
Full Frame Shutter and Dynamic Pixel Reset (DPR) Modes
High Sensitivity
High Signal to Noise
Non-Destructive Read Capable, extremely low noise capable via signal averaging
1.0 kHz to 30.0 MHz Operation
Very Low Dark Current
Completely Integrated Timing and Control
Replaces Entire CCD Systems, Not Just the Sensor
PDS0004 REV J 04/14/09
© Panavision Imaging LLC 2004- 2009 All rights reserved.
Subject to change without notice.
Page 1 of 13




ELIS-1024A-LG pdf, 반도체, 판매, 대치품
Absolute maximum ratings †
Supply voltage range, VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 V to 6.0 V
Digital input current range, II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –16 mA to 16 mA
Operating case temperature range, TC (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -20°C to 70°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to 85°C
Humidity range, RH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-100%, non-condensing
Lead temperature 1.5 mm (0.06 inch) from case for 45 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240°C
Exceeding the ranges specified under “absolute maximum ratings” can damage the device. The values given are for stress ratings
only. Operation of the device at conditions other than those indicated under “recommended operating conditions” is not implied.
Exposing the device to absolute maximum rated conditions for extended periods may affect device reliability and performance.
NOTES:
1. Voltage values are with respect to the device GND terminal.
2. Case temperature is defined as the surface temperature of the package measured directly over the integrated circuit.
Note: Data below 300nm not measured, but device is sensitive to 200 nm. The QE peaks at 675nm.
Shown for un-encapsulated device.
PDS0004 REV J 04/14/09
© Panavision Imaging LLC 2004- 2009 All rights reserved.
Subject to change without notice.
Page 4 of 13

4페이지










ELIS-1024A-LG 전자부품, 판매, 대치품
Non-Destructive Readout (NDRO)
NDRO mode is similar to the standard mode of operation except that the pixels are readout multiple
times for a single integration time. The required signal timings are shown in Figure 3.
CLK
RST
SHT
DATA
VIDEO
t RST
t int1
Video_Out1
Video_Out1
X Clock Cycles
X Clock Cycles
Figure 3: Non-Destructive Readout Timing Diagram.
Dynamic Pixel Reset (DPR) Mode Timing (RM = 1)
In DPR mode the pixels are reset by internal signals, which eliminates the need for using the external
reset pin. When operating in DPR mode RST must be held low otherwise the internal logic will be
held in reset. However, RST does NOT reset the pixels in DPR mode. Since the pixels are
continuously integrating (except the one clock cycle they are being reset) the SHT pin should always
be held high. The first frame readout will be invalid because the pixels will have been integrating for
an unknown period of time. Valid video will be generated during the second frame. The required
signal timings are illustrated in Figure 4.
CLK
RST
SHT
DATA
VIDEO
Pixel1_Readout
Pixel1_Reset
Pixel1_Readout
Pixel1_Reset
t CLK
t DATA
Frame1
Pixel1_t int
Frame2
X Clock Cycles
X Clock Cycles
Figure 4: DPR Mode Timing Diagram.
Pixel 1 was used as an example to show the key timing situations. During the first clock cycle after
DATA is high pixel 1 is readout. Then while pixel 2 is being readout during the second clock cycle
pixel one is being reset. The integration time for pixel 1 then becomes the time between the rising
PDS0004 REV J 04/14/09
© Panavision Imaging LLC 2004- 2009 All rights reserved.
Subject to change without notice.
Page 7 of 13

7페이지



구       성총 13 페이지
다운로드[ ELIS-1024A-LG.PDF 데이터시트 ]
구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

전력 반도체 판매 ( IGBT, TR 모듈, SCR, 다이오드 모듈 )

상호 : 아이지 인터내셔날

사이트 방문 : [ 홈페이지 ] [ 블로그 1 ] [ 블로그 2 ]



링크공유

링크 :

관련 데이터시트

부품번호상세설명 및 기능제조사
ELIS-1024A-LG

High Performance Linear Image Sensors

Panavision Imaging
Panavision Imaging

DataSheet.kr    |   2020   |  연락처   |  링크모음   |   검색  |   사이트맵