|
|
Número de pieza | ICX239AKC | |
Descripción | Diagonal 3mm (Type 1/6) CCD Image Sensor | |
Fabricantes | Sony | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de ICX239AKC (archivo pdf) en la parte inferior de esta página. Total 18 Páginas | ||
No Preview Available ! ICX239AKC
Diagonal 3mm (Type 1/6) CCD Image Sensor for PAL Color Video Cameras
Description
The ICX239AKC is an interline CCD solid-state
image sensor suitable for PAL small color video
cameras. High resolution is achieved hrough the use
of Ye, Cy, Mg, and G complementary color mosaic
filters.
This chip features a field period readout system and
an electronic shutter with variable charge-storage time.
The package is the smallest 12-pin SON (LCC).
12 pin SON (Plastic)
Features
• High sensitivity and low smear
• Horizontal register: 3.3 to 5.0V drive
• Reset gate:
3.3 to 5.0V drive
• No voltage adjustment
(Reset gate and substrate bias are not adjusted.)
• Low dark current and excellent antiblooming characteristics
• Continuous variable-speed shutter
• Recommended range of exit pupil distance: –10mm to –∞
• Ye, Cy, Mg, and G complementary color mosaic filters on chip
• 12-pin MID SON (LCC) package
V
3
Pin 7
Pin 1
2
12
H 40
Device Structure
Optical black position
• Interline CCD image sensor
(Top View)
• Image size:
Diagonal 3mm (Type 1/6)
• Number of effective pixels: 752 (H) × 582 (V) approx. 440K pixels
• Total number of pixels: 795 (H) × 596 (V) approx. 470K pixels
• Chip size:
3.30mm (H) × 2.95mm (V)
• Unit cell size:
3.275µm (H) × 3.150µm (V)
• Optical black:
Horizontal (H) direction: Front 3 pixels, rear 40 pixels
Vertical (V) direction: Front 12 pixels, rear 2 pixels
• Number of dummy bits: Horizontal 22
Vertical 1 (even fields only)
• Substrate material:
Silicon
Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by
any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the
operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits.
–1–
E02471
1 page ICX239AKC
Drive Clock Waveform Conditions
(1) Readout clock waveform
100%
90%
10%
0%
VVT
tr twh
(2) Vertical transfer clock waveform
Vφ1
VVH1
VVHH
VVH
VVHH
VVHL
VVHL
φM
φM
2
tf
0V
Vφ3
VVHL
VVHH
VVHH
VVH3
VVHL
VVH
VVL
VVL1
VVLH
VVLL
Vφ2
VVHH
VVH2 VVHL
VVHH
VVH
VVHL
VVL3
VVL
VVLL
VVLH
Vφ4
VVH
VVHH
VVHH
VVHL
VVHL
VVH4
VVL2VVLH
VVLL
VVL
VVH = (VVH1 + VVH2)/2
VVL = (VVL3 + VVL4)/2
VφV = VVHn – VVLn (n = 1 to 4)
VVLH
VVLL
VVL4
–5–
VVL
5 Page ICX239AKC
5. Video signal shading
Set to standard imaging condition III. With the lens diaphragm at F5.6 to F8, adjust the luminous intensity
so that the average value of the Y signal output is 200mV. Then measure the maximum (Ymax [mV]) and
minimum (Ymin [mV]) values of the Y signal and substitute the values into the following formula.
SHy = (Ymax – Ymin)/200 × 100 [%]
6. Uniformity between video signal channels
Set to standard imaging condition II. Adjust the luminous intensity so that the average value of the Y signal
output is 200mV, and then measure the maximum (Crmax, Cbmax [mV]) and minimum (Crmin, Cbmin
[mV]) values of the R – Y and B – Y channels of the chroma signal and substitute the values into the
following formula.
∆Sr = | (Crmax – Crmin)/200 | × 100 [%]
∆Sb = | (Cbmax – Cbmin)/200 | × 100 [%]
7. Dark signal
Measure the average value of the Y signal output (Ydt [mV]) with the device ambient temperature 60°C and
the device in the light-obstructed state, using the horizontal idle transfer level as a reference.
8. Flicker
1) Fy
Set to standard imaging condition II. Adjust the luminous intensity so that the average value of the Y signal
output is 200mV, and then measure the difference in the signal level between fields (∆Yf [mV]). Then
substitute the value into the following formula.
Fy = (∆Yf/200) × 100 [%]
2) Fcr, Fcb
Set to standard imaging condition II. Adjust the luminous intensity so that the average value of the Y signal
output is 200mV, insert an R or B filter, and then measure both the difference in the signal level between
fields of the chroma signal (∆Cr, ∆Cb) as well as the average value of the chroma signal output (CAr, CAb).
Substitute the values into the following formula.
Fci = (∆Ci/CAi) × 100 [%] (i = r, b)
9. Line crawls
Set to standard imaging condition II. Adjust the luminous intensity so that the average value of the Y signal
output is 200mV, and then insert a white subject and R, G, and B filters and measure the difference
between Y signal lines for the same field (∆Ylw, ∆Ylr, ∆Ylg, ∆Ylb [mV]). Substitute the values into the
following formula.
Lci = (∆Yli/200) × 100 [%] (i = w, r, g, b)
– 11 –
11 Page |
Páginas | Total 18 Páginas | |
PDF Descargar | [ Datasheet ICX239AKC.PDF ] |
Número de pieza | Descripción | Fabricantes |
ICX239AKC | Diagonal 3mm (Type 1/6) CCD Image Sensor | Sony |
ICX239AKE | CCD Image Sensor with Square Pixel for Color Cameras | Sony |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |