|
|
|
부품번호 | LL1005-FH56NK 기능 |
|
|
기능 | Multilayer Chip Inductors | ||
제조업체 | TOKO | ||
로고 | |||
전체 5 페이지수
Multilayer Chip Inductors
LL1005-FH
Series
TYPE LL1005-FH Series
Inductance Range: 1.0~100nH (E-12)
Temperature Coefficient of L: + 250ppm/°C typical
DIMENSIONS /
Length
(mm)
1.0 ± 0.1
Width
(mm)
0.5 ± 0.1
Thickness
(mm)
0.5 ± 0.1
Electrode width
A (mm)
0.25 ± 0.1
• Marking of polarity: Marking is on the upper Surface
of the unit.
•
Marking of polarity
Marking: Blue Green
L
W
T
A
ELECTRICAL CHARACTERISTICS /
• Inductance Range
1.0~100nH (E-12 Series)
• Inductance Tolerance S ; ± 0.3nH (1.0~5.6nH)
J ; ± 5% (6.8~100nH)
K ; ± 10% (3.3~100nH)
• Q (Typ.)
20~34 (at 800MHz)
• Rated Current
150~300mA
• L Temperature
Coefficient (Typ.)
+ 250ppm/°C
• Applicable Temperature
Range
− 40~+ 100°C
PART NUMBERING SYSTEM /
L L 1 0 0 5—F H
Material /
Physical Dimensions /
TOKO's Type name /
Inductance
Unit is nH and 3 digits are used.
The value is indicated as shown below.
Example / 4N7…4.7nH, 27N…27nH
SOLDERING CONDITIONS /
Recommended Pattern
c
b ab
•
•
• 20 ~ 34 (at 800MHz)
•
•
•
Tolerance /
Inductance /
Tolerance for the Inductance
Mark
S
J
K
Tolerance
± 0.3nH
± 5%
± 10%
Pattern Dimensions (unit: mm)
Flow Soldering
Reflow Soldering
a 0.3~0.5
0.3~0.5
b 0.4~0.5
0.3~0.5
c 0.3~0.5
0.3~0.4
Conditions for soldering temperatures are determined as per figures below after prior confirmation that abnormalities are not
evident.
Flow Soldering
7s.
230±5°C
80±20°C
2min.
Reflow Soldering
240°C
225°C
20s.
140~170°C
80s.
2min.
Soldering Iron
2s.
250± 10°C
150± 10°C
2min.
Soldering Iron rating:18W
Multilayer and Chick Film Chip Inductors
TYPE
LL2012 PTL2012
LL1608 PTL1608
LL1005 PTL1005
MECHANICAL & ENVIRONMENTAL CHARACTERISTICS
1. Storage Temperature Range: − 55°C~+ 100°C (0°C~+ 40°C in case of taping used) 2. Operating Temperature Range: − 40°C~+ 100°C
Item Specification
Criteria
Solderd chip on PC board is to be bent down to 2mm as
below drawing
Bending Test
No apparent damage
Vibration Test
Resistance to
soldering heat
Solderability Test
Humidity Test
Dry Heat Test
Cold Test
Temperature
Cycling Test
Temperature
Coefficient
No apparent damage
L : within ± 10%
Q: within ± 20%
No apparent damage
Terminal extent %
: more than 70%
No apparent damage
Terminal surface wet %
: more than 70%
No apparent damage
L : within ± 10%
Q: within ± 20%
No apparent damage
L : within ± 10%
Q: within ± 20%
No apparent damage
L : within ± 10%
Q: within ± 20%
No apparent damage
L : within ± 10%
Q: within ± 20%
L : within ± 10%
(Typical: + 250 ppm/°C)
Apply frequency 10~55Hz, 1.5mm amplitude in each
perpendicular direction for 2 hours.
Pre-heat at 160°C, 2~3 minutes.
Soak into a molten solder bath of 260 ± 5°C for
10 ± 0.5 seconds.
Pre-heat at 160°C, 2~3 minutes.
Soak into a molten solder bath of 230 ± 5°C for
4 ± 1 seconds.
Exposure at 60°C, 95% RH for 1000 hours.
Characteristics are measured after an ambient air exposure
of 2 hours.
Exposure at 100°C, for 1000 hours.
Characteristics are measured after an ambient air exposure
of 2 hours.
Exposure at − 40°C, for 1000 hours.
Characteristics are measured after an ambient air exposure
of 2 hours.
Solder the sample on PC board.
100 cycles at + 100°C for 30 minutes, − 40°C for 30 minutes.
Characteristics are measured after an ambient air exposure
of 2 hours.
Monitor L change throughout temperature of − 40°C to
+ 100°C with reference to L at 20°C.
°C
4페이지 | |||
구 성 | 총 5 페이지수 | ||
다운로드 | [ LL1005-FH56NK.PDF 데이터시트 ] |
당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는 |
구매 문의 | 일반 IC 문의 : 샘플 및 소량 구매 ----------------------------------------------------------------------- IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한 광범위한 전력 반도체를 판매합니다. 전력 반도체 전문업체 상호 : 아이지 인터내셔날 사이트 방문 : [ 홈페이지 ] [ 블로그 1 ] [ 블로그 2 ] |
부품번호 | 상세설명 및 기능 | 제조사 |
LL1005-FH56NJ | Multilayer Chip Inductors | TOKO |
LL1005-FH56NK | Multilayer Chip Inductors | TOKO |
DataSheet.kr | 2020 | 연락처 | 링크모음 | 검색 | 사이트맵 |