ITXG76 데이터시트 PDF

ITXG76 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.



전체 23 페이지수

미리보기를 사용할 수 없습니다

Global LCD Panel Exchange Center

www.panelook.com

Engineering Specification

Engineering Specification

14.1 inches XGA Color TFT/LCD Module

Model Name:ITXG76

Document Control Number : OEM76-05

Note:Specification is subject to change without notice. Consequently it is better to contact to IBM

before proceeding with the design of your product incorporating this module.

Display Business Unit

International Business Machines Corporation

(C) Copyright IBM Corp. 1999,2000 All Rights reserved.

May 24,2000

OEM76-05

1/23

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Engineering Specification

1.0 Handling Precautions

1) Since front polarizer is easily damaged, pay attention not to scratch it.

2) Be sure to turn off power supply when inserting or disconnecting from input connector.

3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.

4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.

5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.

6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth

when handling.

7) Do not open nor modify the Module Assembly.

8) Do not press the reflector sheet at the back of the module to any directions.

9) In case if a Module has to be put back into the packing container slot after once it was taken out

from the container, do not press the center of the CFL Reflector edge.

Instead, press at the far ends of the CFL Reflector edge softly. Otherwise the TFT Module may

be damaged.

10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the

Interface Connector of the TFT Module.

11) After installation of the TFT Module into an enclosure ( Notebook PC Bezel, for example),

do not twist nor bent the TFT Module even momentary. At designing the

enclosure, it should be taken into consideration that no bending/twisting forces are applied

to the TFT Module from outside. Otherwise the TFT Module may be damaged.

12) The fluorescent lamp in the liquid crystal display(LCD) contains mercury. Do not put it in trash that is

disposed of in landfills. Dispose of it as required by local ordinances or regulations.

13) Small amount of materials having no flammability grade is used in the LCD module.

The LCD module should be supplied by power complied with requirements of

Limited Power Source (2.11, IEC60950 or UL1950), or be applied exemption

conditions of flammability requirements (4.4.3.3, IEC60950 or UL1950) in an end product.

14) The LCD module is designed so that the CFL in it is supplied by Limited Current Circuit

(2.4, IEC60950 or UL1950). Do not connect the CFL in Hazardous Voltage Circuit.

y The information contained herein is presented only as a guide for the applications of our

products. No responsibility is assumed by IBM for any infringements of patents or other right

of the third partied which may result from its use. No license is granted by implication or

otherwise under any patent or patent rights of IBM or others.

y The information contained herein may be changed without prior notice. It is therefore

advisable to contact IBM before proceeding with the design of equipment incorporating this

product.

(C) Copyright IBM Corp. 1999,2000 All Rights reserved.

May 24,2000

OEM76-05

4/23

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Engineering Specification

3.0 Absolute Maximum Ratings

Absolute maximum ratings of the module is as follows :

Item

Symbol

Min

Supply Voltage

Logic/LCD Drive Voltage

VDD

-0.3

Input Voltage of Signal

CFL Inrush current

CFL Current

CFL Ignition Voltage

Operating Temperature

Operating Relative Humidity

Storage Temperature

Storage Relative Humidity

Vibration

Shock

Vin

ICFLL

ICFL

Vs

TOP

HOP

TST

HST

-0.3

-

-

-

0

8

-20

5

Max

+4.0

Unit

V

Conditions

VDD+0.3

20

7

1,600

+50

95

+60

95

1.5 10-200

50 18

V

mA

mArms

Vrms

deg.C

%RH

deg.C

%RH

G Hz

G ms

Note 2

Note 1

Note 1

Note 1

Note 1

Half sine wave.

Note 1 : Maximum Wet-Bulb should be 39 degree C and No condensation.

Note 2 : Duration=50 msec Max.

(C) Copyright IBM Corp. 1999,2000 All Rights reserved.

May 24,2000

OEM76-05

7/23

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.