Datasheet.kr   

AOZ1033AI 데이터시트 PDF




Alpha & Omega Semiconductors에서 제조한 전자 부품 AOZ1033AI은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


 

PDF 형식의 AOZ1033AI 자료 제공

부품번호 AOZ1033AI 기능
기능 3A Synchronous Buck Regulator
제조업체 Alpha & Omega Semiconductors
로고 Alpha & Omega Semiconductors 로고


AOZ1033AI 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 15 페이지수

미리보기를 사용할 수 없습니다

AOZ1033AI 데이터시트, 핀배열, 회로
AOZ1033AI
EZBuck™ 3A Synchronous Buck Regulator
General Description
The AOZ1033A is a high efficiency, easy to use, 3A
synchronous buck regulator. The AOZ1033A works from
4.5V to 18V input voltage range, and provides up to 3A of
continuous output current with an output voltage adjust-
able down to 0.8V.
The AOZ1033A comes in a SO-8 package and is rated
over a -40°C to +85°C operating ambient temperature
range.
Features
z 4.5V to 18V operating input voltage range
z Synchronous Buck: 80mΩ internal high-side switch
and 30mΩ internal low-side switch with integrated
schottky diode
z High efficiency: up to 95%
z Internal soft start
z Output voltage adjustable to 0.8V
z 3A continuous output current
z Fixed 600kHz PWM operation
z Pulse skipping at light load for high efficiency over
entire load range
z Cycle-by-cycle current limit
z Pre-bias start-up
z Short-circuit protection
z Thermal shutdown
z SO-8 package
Applications
z Point of load DC/DC converters
z LCD TV
z Set top boxes
z DVD/Blu-ray players/recorders
z Cable modems
z PCIe graphics cards
z Telecom/Networking/Datacom equipment
Typical Application
VIN
C1
22µF
RC
CC
VIN
EN
AOZ1033 LX
COMP
FB
AGND
PGND
L1 4.7µH
R1
R2
VOUT
C2, C3
22µF
Rev. 1.1 October 2010
Figure 1. 3.3V 3A Synchronous Buck Regulator
www.aosmd.com
Page 1 of 15




AOZ1033AI pdf, 반도체, 판매, 대치품
AOZ1033AI
Electrical Characteristics
TA = 25°C, VIN = VEN = 12V, VOUT = 3.3V unless otherwise specified.
Symbol
Parameter
Conditions
VIN
VUVLO
IIN
IOFF
VFB
IFB
VEN
Supply Voltage
Input under-voltage lockout
threshold
Supply current (Quiescent)
Shutdown supply current
Feedback Voltage
Load regulation
Line regulation
Feedback voltage input current
EN input threshold
VHYS EN input hysteresis
MODULATOR
fO
DMAX
tMIN
Frequency
Maximum Duty Cycle
Minimum On Time
Error amplifier voltage gain
Error amplifier transconductance
PROTECTION
ILIM
VOVP
Current Limit
Over-Voltage Protection
Over-temperature shutdown limit
tSS Soft Start Interval
OUTPUT STAGE
High-side switch on-resistance
Low-side switch on-resistance
VIN rising
VIN falling
IOUT = 0, VFB = 1.2V, VEN >1.2V
VEN = 0V
TA = 25°C
Off threshold
On threshold
Off threhsold
On threshold
TJ rising
TJ falling
VIN = 12V
VIN = 5V
VIN = 12V
VIN = 5V
Min.
4.5
0.788
2
400
100
3.8
Typ.
4.1
3.7
1.6
1
0.8
0.5
1
100
450
150
500
200
4.2
960
860
150
100
3
80
130
30
56
Max.
18
2.5
10
0.812
200
0.6
Units
V
V
V
mA
μA
V
%
%
nA
V
V
mV
500 kHz
%
ns
V/V
μA / V
A
mV
mV
°C
°C
ms
100 mΩ
180 mΩ
36 mΩ
70 mΩ
Rev. 1.1 October 2010
www.aosmd.com
Page 4 of 15

4페이지










AOZ1033AI 전자부품, 판매, 대치품
AOZ1033AI
Detailed Description
The AOZ1033A is a current-mode step down regulator
with integrated high-side PMOS switch and a low-side
NMOS switch. It operates from a 4.5V to 18V input volt-
age range and supplies up to 3A of load current. The
duty cycle can be adjusted from 6% to 100% allowing a
wide range of output voltage. Features include enable
control, Power-On Reset, input under voltage lockout,
output over voltage protection, active high power good
state, fixed internal soft-start and thermal shut down.
The AOZ1033A is available in SO-8 package.
Enable and Soft Start
The AOZ1033A has internal soft start feature to limit
in-rush current and ensure the output voltage ramps up
smoothly to regulation voltage. A soft start process
begins when the input voltage rises to 4.1V and voltage
on EN pin is HIGH. In soft start process, the output volt-
age is ramped to regulation voltage in typically 2.2ms.
The 2.2ms soft start time is set internally.
The EN pin of the AOZ1033A is active high. Connect the
EN pin to VIN if enable function is not used. Pull it to
ground will disable the AOZ1033A. Do not leave it open.
The voltage on EN pin must be above 2V to enable the
AOZ1033A. When voltage on EN pin falls below 0.6V, the
AOZ1033A is disabled. If an application circuit requires
the AOZ1033A to be disabled, an open drain or open col-
lector circuit should be used to interface to EN pin.
Steady-State Operation
Under steady-state conditions, the converter operates
in fixed frequency and Continuous-Conduction Mode
(CCM).
The AOZ1033A integrates an internal P-MOSFET as the
high-side switch. Inductor current is sensed by amplifying
the voltage drop across the drain to source of the high
side power MOSFET. Output voltage is divided down by
the external voltage divider at the FB pin. The difference
of the FB pin voltage and reference is amplified by the
internal transconductance error amplifier. The error volt-
age, which shows on the COMP pin, is compared against
the current signal, which is sum of inductor current signal
and ramp compensation signal, at PWM comparator
input. If the current signal is less than the error voltage,
the internal high-side switch is on. The inductor current
flows from the input through the inductor to the output.
When the current signal exceeds the error voltage, the
high-side switch is off. The inductor current is freewheel-
ing through the internal low-side N-MOSFET switch to
output. The internal adaptive FET driver guarantees no
turn on overlap of both high-side and
low-side switch.
Comparing with regulators using freewheeling Schottky
diodes, the AOZ1033A uses freewheeling NMOSFET to
realize synchronous rectification. It greatly improves the
converter efficiency and reduces power loss in the
low-side switch.
The AOZ1033A will enter the discontinuous conduction
mode at light load. Several pulses may be skipped in
between switching cycles at very light load, it further
improving light load efficiency.
The AOZ1033A uses a P-Channel MOSFET as the
high-side switch. It saves the bootstrap capacitor nor-
mally seen in a circuit which is using an NMOS switch. It
allows 100% turn-on of the high-side switch to achieve
linear regulation mode of operation. The minimum volt-
age drop from VIN to VO is the load current times DC
resistance of MOSFET plus DC resistance of buck induc-
tor. It can be calculated by equation below:
VO_MAX = VIN IO × RDS(ON)
where;
VO_MAX is the maximum output voltage;,
VIN is the input voltage from 4.5V to 18V,
IO is the output current from 0A to 3A, and
RDS(ON) is the on resistance of internal MOSFET. The value is
between 97mΩ and 200mΩ depending on input voltage and
junction temperature.
Switching Frequency
The AOZ1033A switching frequency is fixed and set by
an internal oscillator. The practical switching frequency
could range from 500kHz to 700kHz due to device varia-
tion.
Output Voltage Programming
Output voltage can be set by feeding back the output to
the FB pin by using a resistor divider network. In the
application circuit shown in Figure 1. The resistor divider
network includes R1 and R2. Usually, a design is started
by picking a fixed R2 value and calculating the required
R1 with equation below.
VO
=
0.8
×
1
+
R-----1-⎟⎞
R2
Some standard value of R1, R2 and most used output
voltage values are listed in Table 1 on the next page.
Rev. 1.1 October 2010
www.aosmd.com
Page 7 of 15

7페이지


구       성 총 15 페이지수
다운로드[ AOZ1033AI.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
AOZ1033AI

3A Synchronous Buck Regulator

Alpha & Omega Semiconductors
Alpha & Omega Semiconductors

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵