Datasheet.kr   

V39CH8 데이터시트 PDF




Littelfuse에서 제조한 전자 부품 V39CH8은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


PDF 형식의 V39CH8 자료 제공

부품번호 V39CH8 기능
기능 Surface Mount Varistors
제조업체 Littelfuse
로고 Littelfuse 로고


V39CH8 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 6 페이지수

미리보기를 사용할 수 없습니다

V39CH8 데이터시트, 핀배열, 회로
Varistor Products
Surface Mount Varistors > CH Series
RoHS CH Varistor Series
Agency Approvals
Recognized under the components program of
Underwriters Laboratories.
AGENCY
AGENCY FILE NUMBER
UL E320116
Description
CH Series transient surge suppressors are small,
metal-oxide varistors (MOVs) manufactured in leadless
chip form. They are intended for use in a variety of
applications from low voltage DC to off-line board-level
protection. These devices, which have significantly
lower profiles than traditional radial lead varistors,
permit designers to reduce the size and weight and
increase the reliability of their equipment designs.
CH Series varistors are available in a voltage range from
14V to 275V (VM(AC)RMS), and energy ratings up to 8J.
See the Littelfuse Multilayer Suppressor Series also.
Features
t -FBEoGSFF
t -FBEMFTT TVSGBDF
mount chip in 5
x 8mm Size
t 7PMUBHFSBUJOHT
VM(AC)RMS 14V to 275V
t 4VQQMJFEJOUBQFBOE
reel or bulk pack
t /PEFSBUJOHVQUP
125ºC ambient
Absolute Maximum Ratings
t'PSSBUJOHTPGJOEJWJEVBMNFNCFSTPGBTFSJFT TFF%FWJDF3BUJOHTBOE4QFDJmDBUJPOTDIBSU
Continuous
Steady State Applied Voltage:
Transient:
AC Voltage Range (VM(AC)RMS)
DC Voltage Range (VM(DC))
Peak Pulse Current (ITM)
For 8/20μs Current (See Figure 2)
Single Pulse Energy Range
For 10/1000μs Current Wave (WTM)
Operating Ambient Temperature Range (TA)
Storage Temperature Range (TSTG)
Temperature Coefficient (DV) of Clamping Voltage (VC) at Specified Test Current
CH Series
14 to 275
18 to 369
100 to 250
1.0 to 8.0
-55 to +125
-55 to +150
<0.01
Units
V
V
A
J
ºC
ºC
%/ºC
CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of
the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
©2010 Littelfuse, Inc.
Specifications are subject to change without notice.
Please refer to www.littelfuse.com/series/CH.html for current information.
Revision: August 30, 2010
CH Varistor Series




V39CH8 pdf, 반도체, 판매, 대치품
Varistor Products
Surface Mount Varistors > CH Series
Lead (Pb) Soldering Recommendations
The principal techniques used for the soldering of
components in surface mount technology are IR Re-flow
and Wave soldering. Typical profiles are shown on the right.
CH series devices have silver-platinum terminals (Ag/Pt),
and the recommended solder is 62/36/2 (Sn/Pb/Ag), 60/40
(Sn/Pb) or 63/37 (Sn/Pb). Littelfuse also recommends an
RMA solder flux.
Wave soldering is the most strenuous of the processes.
To avoid the possibility of generating stresses due to
thermal shock, a preheat stage in the soldering process
is recommended, and the peak temperature of the solder
process should be rigidly controlled.
When using a reflow process, care should be taken to
ensure that the CH chip is not subjected to a thermal
gradient steeper than 4 degrees per second; the ideal
gradient being 2 degrees per second. During the soldering
process, preheating to within 100 degrees of the solder's
peak temperature is essential to minimize thermal shock.
Once the soldering process has been completed, it is
still necessary to ensure that any further thermal shocks
are avoided. One possible cause of thermal shock is hot
printed circuit boards being removed from the solder
process and subjected to cleaning solvents at room
temperature. The boards must be allowed to cool gradually
to less than 50ºC before cleaning.
Lead–free (Pb-free) Soldering Recommendations
CH series devices have silver-platinum terminals (Ag/Pt),
and the recommended Lead-free solder is 96.5/3.0/0.5
(SnAgCu) with an RMA flux, though there is a wide
selection of pastes and fluxes available that should be
compatible.
The reflow profile must be constrained by the maximums
in the Lead–free Reflow Profile. For Lead–free Wave
soldering, the Wave Solder Profile still applies.
Note: the Lead–free paste, flux and profile were used for
evaluation purposes by Littelfuse, based upon industry
standards and practices. There are multiple choices of all
three available, it is advised that the customer explores the
optimum combination for their process as processes vary
considerably from site to site.
Reflow Solder Profile
250
MAXIMUM TEMPERATURE
230°C
200
40-80
SECONDS
ABOVE 183°C
150
RAMP RATE
<2°C/s
100
PREHEAT DWELL
50 PREHEAT ZONE
0
0
Figure 7
0.5 1.0
1.5 2.0 2.5 3.0 3.5 4.0
TIME (MINUTES)
Wave Solder Profile
300
MAXIMUM WAVE 260°C
250
200
150
SECOND PREHEAT
100
FIRST PREHEAT
50
0
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5
Figure 8
TIME (MINUTES)
Lead–free Re-flow Solder Profile
300
MAXIMUM TEMPERATURE 260˚C,
TIME WITHIN 5˚C OF PEAK
250 20 SECONDS MAXIMUM
RAMP RATE
200
<3˚C/s
60 - 150 SEC
> 217˚C
150
100 PREHEAT ZONE
50
0
0 1.0 2.0 3.0 4.0 5.0 6.0 7.0
Figure 9
TIME (MINUTES)
CH Varistor Series
Revision: August 30, 2010
©2010 Littelfuse, Inc.
Specifications are subject to change without notice.
Please refer to www.littelfuse.com/series/CH.html for current information.

4페이지












구       성 총 6 페이지수
다운로드[ V39CH8.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
V39CH8

Surface Mount Varistors

Littelfuse
Littelfuse

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵