Datasheet.kr   

TL-T2Y2 데이터시트 PDF




Omron에서 제조한 전자 부품 TL-T2Y2은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


PDF 형식의 TL-T2Y2 자료 제공

부품번호 TL-T2Y2 기능
기능 Slim Proximity Sensor
제조업체 Omron
로고 Omron 로고


TL-T2Y2 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 14 페이지수

미리보기를 사용할 수 없습니다

TL-T2Y2 데이터시트, 핀배열, 회로
Slim Proximity Sensor
TL-T
Slim Model of Width 12 mm.
• Ideal for side-by-side mounting.
Be sure to read Safety Precautions on page 5.
Ordering Information
Appearance
Sensing distance
Output specifications
Model
Output configuration
Shielded
2 mm
DC 3-wire models
AC 2-wire models
NPN
PNP
NO
TL-T2E1
TL-T2F1
TL-T2Y1
NC
TL-T2E2
---
TL-T2Y2
Unshielded
5 mm
DC 3-wire models NPN
AC 2-wire models
TL-T5ME1
TL-T5MY1
TL-T5ME2
TL-T5MY2
Note: Models with a different frequency are available. The model numbers are TL-T@@@5. (e.g., TL-T2E15).
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2008 All Rights Reserved.
1




TL-T2Y2 pdf, 반도체, 판매, 대치품
I/O Circuit Diagrams
DC 3-wire Models
Operation Output
mode specifications
Models
TL-T2E1
NO TL-T5ME1
NPN
TL-T2E2
NC TL-T5ME2
Timing charts
Sensing object Present
Not present
Load
(between brown
and black)
Operate
Reset
Output voltage
(between black
and blue)
Detection
indicator (red)
H
L
ON
OFF
Sensing object Present
Not present
Load
(between brown
and black)
Operate
Reset
Output voltage
(between black
and blue)
Detection
indicator (red)
H
L
ON
OFF
NO
PNP
TL-T2F1
Sensing object Present
Not present
Load
(between brown
and black)
Operate
Reset
Output voltage
(between black
and blue)
Detection
indicator (red)
H
L
ON
OFF
AC 2-wire Models
Operation mode
Models
TL-T2Y1
NO TL-T5MY1
Timing charts
Sensing object Present
Not present
Load
Operate
Reset
Detection indicator
(red)
ON
OFF
NC
TL-T2Y2
TL-T5MY2
Sensing object Present
Not present
Load
Operate
Reset
Detection indicator ON
(red)
OFF
TL-T
Output circuits
Brown
+V
Proxim-
ity
Sensor
main
circuit
4.7 kΩ
2.2 Ω
Load
Black *1
Out-
put
*2
Tr
Blue
0V
*1. 200 mA (load current)
*2. When a transistor is connected
Proxim-
ity
Sensor
main
circuit
4.7 kΩ
2.2 Ω
Brown
+V
Black*2
Tr
Out-
put *1
Load
Blue
0V
*1. 200 mA (load current)
*2. When a transistor is connected
Output circuits
Proxi-
mity
Sensor
main
circuit
Brown
Load
Blue
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2008 All Rights Reserved.
4

4페이지










TL-T2Y2 전자부품, 판매, 대치품
Proximity Sensors Technical Guide
Precautions for Correct Use
The following conditions must be considered to understand the conditions of the application and location as well as the relation to control
equipment.
Model Selection
Item
Check the relation between the sensing object
and the Proximity Sensor.
Points of consideration
Specific condi- Direction of ob-
tions of object ject movement
Peripheral metal Sensing distance
Sensing
object and
operating
condition of
Proximity
Sensor
Sensing object
Sensing
distance
Surrounding
metals
Proximity Sensor
Material, size, Transit interval, Material, distance Fluctuation in
shape, existence speed, existence to Sensor, orien- transit point, al-
of plating, etc. of vibration, etc. tation, etc.
lowable error, etc.
Sensing (set) distance, shape of Sensor (rectangular, cylindrical, through-
beam, grooved), influence of peripheral metal (Shielded Sensors, Non-
shielded Sensors), response speed (response frequency), influence of
temperature, influence of voltage, etc.
Electrical
conditions
Environ-
mental
conditions
Verify the electrical conditions of the control system
to be used and the electrical performance of the
Proximity Sensor.
Power
supply
DC (voltage fluctuation, current capac-
ity value)
AC (voltage fluctuation, frequency,
etc.)
Need for S3D2 Controller
Selecting the power
supply type
{DC
DC + S3D2 Controller
AC
Output Load
Load
Resistive load - Non-contact control
system
Inductive load - Relay, solenoid, etc.
Steady-state current, inrush current
Operating, reset voltage (current)
Lamp load
Steady-state current, inrush current
Open/close frequency
Selecting the power
supply type
{DC
DC + S3D2 Controller
AC
Control output
Maximum current
(voltage)
Leakage current
Residual load voltage
The environmental tolerance of the Proximity Sensor
Water Resistance
is better than that of other types of Sensors. However, Do not use the Sensor in water, rain, or outdoors.
investigate carefully before using a Proximity Sensor
under harsh temperatures or in special atmospheres.
Ambient Conditions
To maintain reliability of operation, do not use the
Temperature
and humidity
Highest or lowest
values, existence
of direct sunlight,
etc.
Temperature influence, Sensor outside the specified temperature range or
high-temperature use, outdoors. Even though the Proximity Sensor has a
low temperature use,
need for shade, etc.
water-resistant structure, it must be covered to pre-
vent direct contact with water or water-soluble cut-
ting oil. Do not use the Sensor in atmospheres with
Atmosphere
Water, oil, iron
powder, or other
Need
tance
for water resis-
or oil resistance,
chemical vapors, in particular, strong alkalis or ac-
ids (nitric acid, chromic acid, or hot concentrated
sulfuric acid).
special chemicals need for explosion-
proof structure
Explosive Atmospheres
Vibration and Size, duration
shock
Need for strength,
mounting method
Do not use the Sensor in atmospheres where
there is a danger of explosion. Use an Explosion-
proof Sensor.
When deciding the mounting method, take into consideration not
only restrictions due to mechanical devices, but also ease of main-
tenance and inspection, and interference between Sensors.
Mounting
conditions
Wiring method,
existence of in-
ductance surges
Connection
Wires
Wire type, length, oil-resistant
cable, shielded cable, robot
cable, etc.
Conduits, ducts, pre-wired,
terminal wiring, ease of main-
tenance and inspection
Mounting procedure
Installation location
Existence of mounting
brackets, direct mounting,
secured with bolts or screws
Ease of maintenance and
inspection, mounting space
Influence of
external
electromag-
netic fields
Other con-
siderations
The influence within a DC magnetic field is 20 mT* max. Do not use the Sensor at a level higher than 20 mT.
Sudden changes in the DC magnetic field may cause malfunction. Do not use the Sensor for applications that involve turning a
DC electromagnet ON and OFF.
Do not place a transceiver near the Sensor or its wiring. Doing so may cause malfunction.
Cost feasibility: Price/delivery time
Life: Power-ON time/frequency of use
* mT (millitesla) is a unit for expressing magnetic flux density. One tesla is the equivalent of 10,000 gauss.
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2008 All Rights Reserved.
C-2

7페이지


구       성 총 14 페이지수
다운로드[ TL-T2Y2.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
TL-T2Y1

Slim Proximity Sensor

Omron
Omron
TL-T2Y2

Slim Proximity Sensor

Omron
Omron

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵