EM3502 Datasheet PDF - Schneider
| Part Number | EM3502 | |
| Description | Compact Power and Energy Meter Manual | |
| Manufacturers | Schneider | |
| Logo |  |
|
|
There is a preview and EM3502 download ( pdf file ) link at the bottom of this page. Total 30 Pages | ||
Preview 1 page No Preview Available !
EM3502, EM3550
Compact Power and Energy Meter
Installation Guide
ZL0092-0A
11/2011
|
| |
 
ZL0092-0A
11/2011
EM3502, 3550
Safety Precautions
SAFETY PRECAUTIONS
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
• Follow safe electrical work practices. See NFPA 70E in the USA or
applicable local codes.
• This equipment must only be installed and serviced by qualified
electrical personnel.
• Read, understand, and follow the instructions before installing this
product.
• Turn off all power supplying equipment before working on or inside
the equipment.
• Always use a properly rated voltage sensing device to confirm power is
off.
• DO NOT DEPEND ON THIS PRODUCT FOR VOLTAGE INDICATION.
• Only install this product on insulated conductors.
• Install device in an appropriate electrical and fire enclosure per local
regulations.
• ESD sensitive equipment. Ground yourself and discharge any static
charge before handling this device.
• Any covers that may be displaced during the installation must be
reinstalled before powering the unit.
• Do not install on the load side of a Variable Frequency Drive (VFD), aka
Variable Speed Drive (VSD) or Adjustable Frequency Drive (AFD).
Failure to follow these instructions will result in death or serious injury.
INSTALLATION OVERVIEW
The meter can be mounted in two ways: on standard 35 mm DIN rail or
screw-mounted to the interior surface of the enclosure.
A. DIN Rail Mounting
1. Disconnect and lock out power. Use a properly rated voltage sensing device
to confirm power is off.
2. Attach mounting clips to the underside of the housing by sliding them into
the slots from the inside. The stopping pegs must face the housing, and the
outside edge of the clip must be flush with the outside edge of the housing.
3. Snap the clips onto the DIN rail.
4. To prevent horizontal shifting across the DIN rail, use two end stop clips.
B. Screw Mounting
1. Disconnect and lock out power. Use a properly rated voltage sensing device
to confirm power is off.
2. Attach the mounting clips to the underside of the housing by sliding them
into the slots from the outside. The stopping pegs must face the housing,
and the screw hole must be exposed on the outside of the housing.
3. Use three #8 screws (not supplied) to mount the meter to the inside of the
enclosure.
NOTE: For detailed instructions, please see the “Installation” section
later in this guide.
© 2011 Schneider Electric All Rights Reserved.
1
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for EM3502 electronic component. |
| Information | Total 30 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ EM3502.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| EM3502 | The function is Compact Power and Energy Meter Manual. Schneider | |
| EM3503 | The function is Euro-Mag Terminal Blocks. Cooper Bussmann |  |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
EM35
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||