|
|
|
부품번호 | KIA6283K 기능 |
|
|
기능 | 4.6W DUAL AUDIO POWER AMPLIFIER | ||
제조업체 | KEC | ||
로고 | |||
전체 7 페이지수
SEMICONDUCTOR
TECHNICAL DATA
KIA6283K
BIPOLAR LINEAR INTEGRATED CIRCUIT
4.6W DUAL AUDIO POWER AMPLIFIER
KIA6283K is an audio power IC with built-in two channels developed
for portable radio cassette tape recorder. Because of the parts reduction
and SIP (Single In line Package), space merit is remarkable.
Themal shut down protection circuit is built in.
A
F
S
Q
B
FEATURES
High Power
POUT=2.5W/CH (Typ.)
: (VCC=9V, RL=4 , f=1kHz, THD=10%)
POUT=4.6W/CH(Typ.)
: (VCC=12V, RL=4 , f=1kHz, THD=10%)
Low popping noise at power ON
Small Quiescent Current
: ICCQ=19mA (Typ.) (VCC=9V, VIN=0)
Soft Clip
Built-in thermal shut down protection circuit
Best for supply voltage 9V, 12V
Operation supply voltage range : VCC=6 15V.
DETAIL "A"
P
d
D1
d
D2
DETAIL "A"
T
DIM MILLIMETERS
A 29.7+_ 0.2
B 4.0 +_ 0.2
D1 0.6+_ 0.1
D2 0.7+_ 0.1
d 0.5+_ 0.1
F 28.0+_ 0.2
G 0.5+_ 0.2
H1 8.5+_ 0.3
H2 15.0+_ 0.3
L1 2.5+_ 0.2
L2 5.5+_ 0.2
P 2.54
Q R1.6
R 0.4
S 22.0+_ 0.2
T 0.4+0.1/-0.05
SSIP-12
MAXIMUM RATING (Ta=25 )
CHARACTERISTIC
SYMBOL
Supply Voltage
Output Current (Peak/CH)
Power Dissipation
Operating Temperature
Storage Temperature
VCC
IO(peak)
PD
Topr
Tstg
RATING
20
2.5
12.5
-20 75
-55 150
UNIT
V
A
W
1994. 10. 31
Revision No : 0
1/8
KIA6283K
APPLICATION INFORMATION AND APPLICATION METHOD
1. ADJUSTMENT OF VOLTAGE GAIN
The voltage gain Gv is obtained as follows by R1, R2 and Rf in Fig. 1.
GV = 20 log
Rf+R1+R2
Rf+R1
Rf
When Rf=0, Gv=56dB(Typ.)
When Rf=82 , Gv=45dB(Typ.)
By increasing Rf, reduction of Gv is Possible. However, since the feedback
increase is liable to produce oscillation, it is recommended to use this at 40dB or over.
5/7 INPUT
R1
4/8 30Ω
+
AMP
-
R2
20kΩ
Fig 1.
2/10
OUTPUT
2. THERMAL SHUT-DOWN CIRCUIT
The thermal shut-down circuit is built in for the purpose of preventing the destruction of IC due to the abnormal temperature rise
when the heat radiation is insufficient. The operation temperature is set at radiation Fin temperature 175 (Typ.) At this temperature
or over the bias is interrupted to prevent the destruction of IC.
3. INPUT STAGE
The input circuit of this IC is as shown in Fig. 2. PNP TR:Q1 is provided in
the input circuit so as to make its usage possible without the input coupling
capacitor. However, at pins and , max 60mV offset voltage is produced.
Application after checking volume slide noise is recommended.
For cutting the volume slide noise, insert the input capacitor :
CIN in series to interrupt the DC compornent.
Q2 Q3
OUTPUT
20kΩ
2/10
4. OSCILLATION PREVENTIVE MEASURES
For oscillation preventive capacitor C6 and C7 between
the output terminal and GND, it is recommended to use
polyester film capacitor having good characteristics for
INPUT
5/7 Q1
CIN
temperature and for high frequency.
Since the characteristics of the capacitor is liable to be
influenced by the temperature, use this capacitor after the temperature
6
Pre-GND
test to check the oscillation allowance. In addition, as the position
of the electrolytic capacitor has a remarkable influence on the oscillation,
connect C10 to VCC at the nearest possible position from power GND.
At using this application with the voltage gain reduced, oscillation is liable
to be produced. Apply the capacitor after checking enough for its capacity,
type and mounting position.As the oscillation allowance varies according to the printed
pattern layout, the standard printd board of KEC is recommended to be referred to for design it.
to DRIVER
to BIAS
4/8
Fig. 2
5. INPUT VOLTAGE
When the excessive signal is input, turning-up is produced in the clip waveform.
The turning-up point is VIN=300mVrms(Typ.) : VCC=9V, RL=4 , f=1kHz : Enough care must be taken for this phenomenon.
1994. 10. 31
Revision No : 0
4/8
4페이지 KIA6283K
C.T - f
0
VCC =9V
R L=4Ω
-20 Rg =600Ω
VOUT =0dBm
-40
-60
-80
0.03 0.1
0.3 1
3 10
FREQUENCY f (kHz)
30 100
PD MAX - VCC
12
f=1kHz
THD=10%
10
8
6 R L=2Ω
4 R L=4Ω
2
0
0 2 4 6 8 10 12 14 16
SUPPLY VOLTAGE VCC (V)
PD - POUT
5
RL=4Ω
4
VCC =12V
f=1kHz
3
2 VCC =9V
1
VCC =6V
0
0 1 23 456
OUTPUT POWER POUT (W)
PD - P OUT
5
RL=2Ω
VCC =9V
f=1kHz
4
RL=3Ω
3
2 RL=4Ω
1
0
0 1 2 3 4 56
OUTPUT POWER POUT (W)
14
1
12
10
2
8
6
3
4
4
2
PD - Ta
1 INFINITE HEAT SINK
2 80cm2 x2mm
Al HEAT SINK
3 18cm2 x2mm
Al HEAT SINK
4 NO HEAT SINK
0
0 20 40 60 80 100 120 140 160
AMBIENT TEMPERATURE Ta ( C)
1994. 10. 31
Revision No : 0
10
8
6
4
2
0
0
POUT - VCC
f=1kHz
THD=10%
4 8 12 16 20
SUPPLY VOLTAGE VCC (V)
24
7/8
7페이지 | |||
구 성 | 총 7 페이지수 | ||
다운로드 | [ KIA6283K.PDF 데이터시트 ] |
당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는 |
구매 문의 | 일반 IC 문의 : 샘플 및 소량 구매 ----------------------------------------------------------------------- IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한 광범위한 전력 반도체를 판매합니다. 전력 반도체 전문업체 상호 : 아이지 인터내셔날 사이트 방문 : [ 홈페이지 ] [ 블로그 1 ] [ 블로그 2 ] |
부품번호 | 상세설명 및 기능 | 제조사 |
KIA6283K | 4.6W DUAL AUDIO POWER AMPLIFIER | KEC |
DataSheet.kr | 2020 | 연락처 | 링크모음 | 검색 | 사이트맵 |