Datasheet.kr   

LD7120A 데이터시트 PDF




Leadtrend에서 제조한 전자 부품 LD7120A은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


PDF 형식의 LD7120A 자료 제공

부품번호 LD7120A 기능
기능 Single Synchronous Buck PWM Controller
제조업체 Leadtrend
로고 Leadtrend 로고


LD7120A 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.



전체 9 페이지수

미리보기를 사용할 수 없습니다

LD7120A 데이터시트, 핀배열, 회로
LD7120A
12/14/2006
REV:00
Single Synchronous Buck PWM Controller
General Description
The LD7120A is a single PWM controller designed to drive
N-channel MOSFET in a synchronous buck topology. The IC
integrates the controller, output adjustment, monitoring, and
protection functions in a single 8-pin package.
The LD7120A provides simple, single feedback loop,
voltage mode controller with fast transient response.
Internal 0.8V temperature-compensated reference voltage
is designed to meet low output voltage for further
applications. A fixed 300KHz frequency oscillator reduces
design complexity, while balancing typical application cost
and efficiency.
The LD7120A features over current protection. The output
current is monitored by sensing the voltage drop across the
MOSFET RDS(ON), which eliminates the need for a current
sensing resistor.
Features
Operates from 5V
Drives Two N-channel MOSFETs
Fixed 300KHz Constant Switching Frequency
Full 0~100% Duty-cycle
Programmable Over Current Protection
Internal Soft-start
Fast Transient Response
Under-voltage Lockout
Applications
Motherboard
Graphic Cards
5V Input DC/DC Converter
Memory Supplies
Cable Modem, Set Top Box and DSL Modems
DSP and Core Communications Processor Supplies
Typical Application
Vin= 5V
R3
6.19K
R2
10K
C10
8.2nF
R1
1K
C12
0.1uF
C7
1uF
C5 C6
330uF 330uF
5
7
C9
470pF
6
VCC
1
BOOT
OCSET
2
UGATE
LD7120A
8
PHASE
FB
4
LGATE
GND
3
Q1
Q2
C8
1uF
D1
CH551H-30
C1
0.1uF
L1 2uH
R6
NC
R4
2.15K
C13
NC
Leadtrend Technology Corporation
LD7120A-DS-00 December 2006
R5
62 ohm
C11
18nF
R7
0 ohm
1
Vout
C2 C3 C4
470uF 470uF 0.1uF




LD7120A pdf, 반도체, 판매, 대치품
LD7120A
Electrical Characteristics
(TA = +25oC unless otherwise stated, VCC=5.0V)
PARAMETER
CONDITIONS
Vcc Supply Current
Nominal Supply
Power On Reset
Rising VCC POR Threshold
UGATE and LGATE Open
UCOMP=1.1V, No switching
VCC POR Threshold Hysteresis
Oscillator
Frequency
Ramp Amplitude
VCC=5V
Reference
Reference Voltage Tolerance
Nominal Reference Voltage
Error Amplifier
DC Gain
Gain Bandwidth Product
Gate Drivers
Upper Gate Source Current
Upper Gate Sink Current
Lower Gate Source Current
Lower Gate Sink Current
Protection/Disable
OCSET Current Source
Disable Threshold
MIN
TYP
MAX UNITS
2.0 mA
4.1 4.3 4.5 V
0.4 V
250 300 350 KHz
1.5 Vp-p
2%
0.8 V
70
10
dB
MHz
-1 A
1A
-1 A
2A
17.5
20
22.5
µA
0.8 V
Leadtrend Technology Corporation
LD7120A-DS-00 December 2006
4

4페이지










LD7120A 전자부품, 판매, 대치품
LD7120A
Vin
1uF
VCC
D1
1 BOOT
2 UGATE
8
Vcc
4
PHASE
LGATE
LD7120A
Q1
Cboot
0.1uF
Q2
Vout
Fig. 9
Layout Consideration
Layout is very important in high switching convert design.
There are two sets of critical components in DC/DC
converter using LD7120A.The switching components are
the most critical because they switch large amount of
energy, and therefore tend to generate large amount of
noise. Next are the small signal components, which connect
to sensitive nodes, or those supplying critical bypass current
and signal coupling. Care should be taken to separate these
two sets of components and their associated grounds.
Below are some guidelines for PCB layout while using
LD7120A.
1. Keep the bypass capacitor 1µF very close to IC
(<5mm).
2. Keep output voltage feed back network, FB pin and
OCSET pin related components (small signal
components) very close to IC.
3. Signal ground plane of FB and OCSET pin (small signal
components) should be connected to the power ground
plane with a via or only one point to minimize the effect
of power ground currents.
4. Switching node such as BOOT, UGATE, PHASE and
LGATE should be kept as small as possible and routed
away from FB and OCSET pin.
5. The PCB traces carrying discontinuous currents and
any high current path should be made as short and
wide as possible.
6. If possible, a multi-layer PCB is recommended. Please
refer to the EV kit of LD7120A for a PCB layout
example.
Leadtrend Technology Corporation
LD7120A-DS-00 December 2006
7

7페이지


구       성 총 9 페이지수
다운로드[ LD7120A.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
LD7120

Single Synchronous Buck PWM Controller

Leadtrend
Leadtrend
LD7120A

Single Synchronous Buck PWM Controller

Leadtrend
Leadtrend

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵