Datasheet.kr   

BD9240FV PDF 데이터시트 : 부품 기능 및 핀배열

부품번호 BD9240FV
기능 Silicon Monolithic Integrated Circuit
제조업체 Rohm
로고 Rohm 로고 



전체 5 페이지

		

No Preview Available !

BD9240FV 데이터시트, 핀배열, 회로
1/4
STRUCTURE
NAME OF PRODUCT
Silicon Monolithic Integrated Circuit
DC-AC Inverter Control IC
TYPE BD9240F / BD9240FV
FUNCTION
20V High voltage process
2CH control with Push-Pull
Lamp current and voltage sense feed back control
・ Sequencing easily achieved with Soft Start Control
Short circuit protection with Timer Latch
Under Voltage Lock Out
Mode-selectable the operating or stand-by mode by stand-by pin
・ Automatic Judge function for External synchronization of lamp oscillation
・ BURST mode controlled by PWM and DC input
○ Absolute Maximum Ratings(Ta=25℃)
Parameter
Supply Voltage
Operating Temperature Range
Storage Temperature Range
Maximum Junction Temperature
Power Dissipation
Symbol
VCC
Topr
Tstg
Tjmax
Pd
Limits
20
-40~+85
-55~+150
+150
*1 1063 (BD9240FV)
*2 750 (BD9240F)
Unit
V
mW
*1Pd derate at 8.5mW/℃ for temperature above Ta = 25℃ (When mounted on a PCB 70.0mm×70.0mm×1.6mm)
*2Pd derate at 6.0mW/℃ for temperature above Ta = 25℃ (When mounted on a PCB 70.0mm×70.0mm×1.6mm)
○ Operating condition
Parameter
Supply voltage
oscillation frequency
BCT oscillation frequency
Symbol
VCC
FOUT
FBCT
Limits
8.0 ~ 19.0
30 ~ 90
0.05 ~ 1.00
Unit
V
kHz
kHz
www.DataSheet4U.com
REV. A




BD9240FV pdf, 반도체, 판매, 대치품
4/4
〇NOTE FOR USE
1. This product is produced with strict quality control, but might be destroyed if used beyond its absolute maximum ratings. Once IC is destroyed,
failure mode will be difficult to determine, like short mode or open mode. Therefore, physical protection countermeasure, like fuse is
recommended in case operating conditions go beyond the expected absolute maximum ratings.
2. The circuit functionality is guaranteed within of ambient temperature operation range as long as it is within recommended operating range. The
standard electrical characteristic values cannot be guaranteed at other voltages in the operating ranges, however the variation will be small.
3. Mounting failures, such as misdirection or miscounts, may harm the device.
4. A strong electromagnetic field may cause the IC to malfunction.
5. The GND pin should be the location within ±0.3V compared with the PGND pin.
6. BD9240F/FV incorporate a built-in thermal shutdown circuit (TSD circuit). The thermal shutdown circuit (TSD circuit) is designed only to shut
the IC off to prevent runaway thermal operation. It is not designed to protect the IC or guarantee its operation of the thermal shutdown circuit
is assumed.
7. Absolute maximum ratings are those values that, if exceeded, may cause the life of a device to become significantly shortened. Moreover, the
exact failure mode caused by short or open is not defined. Physical countermeasures, such as a fuse, need to be considered when using a
device beyond its maximum ratings.
8. About the external FET, the parasitic Capacitor may cause the gate voltage to change, when the drain voltage is switching. Make sure to leave
adequate margin for this IC variation.
9. Under operating CP charge (under error mode) analog dimming and burst dimming are not operate.
10. By STB and PH voltage, BD9240F/FV are changed to 3 states. Therefore, do not input STB and PH pin voltage between one state and the other
state (0.8~2.0V, VCC×0.5~VCC×0.85 V)
11. By the DUTY1 pin for setting of Burst dimming Mode, When Burst dimming by DC signal do not input DUTY1 voltage between one state and the
other state (0.485~0.515V, 1.985~2.015V)
When Burst dimming by PWM signal, set ON time and OFF time of the input PWM pulse signal to more than 30us (Dimming of 0% and Dimming
of 100% are no problem)
12. The pin connected a connector need to connect to the resistor for electrical surge destruction.
13. This IC is a monolithic IC which (as shown is Fig.1)has P+ substrate and between the various pins. A P-N junction is formed from this P layer
of each pin. For example, the relation between each potential is as follows,
○(When GND > PinB and GND > PinA, the P-N junction operates as a parasitic diode.)
○(When PinB > GND > PinA, the P-N junction operates as a parasitic transistor.)
Parasitic diodes can occur inevitably in the structure of the IC. The operation of parasitic diodes can result in mutual interference among circuits
as well as operation faults and physical damage. Accordingly you must not use methods by which parasitic diodes operate, such as applying a
voltage that is lower than the GND (P substrate) voltage to an input pin.
www.DataSheet4U.com
Resistance
(PinA)
P
P
N
P
P substrate
GND
Parasitic diode
Transistor (NPN)
(PinB)
B
C
E
N
GND
N
P substrate
GND
Parasitic diode
N
(PinB)
(PinA)
Parasitic diode
B C
E
GND
GND
Other adjacent components
Parasitic diode
Fig.1 Simplified structure of a Bipolar IC
REV. A

4페이지













구       성총 5 페이지
다운로드[ BD9240FV.PDF 데이터시트 ]
구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

전력 반도체 판매 ( IGBT, TR 모듈, SCR, 다이오드 모듈 )

휴대전화 : 010-3582-2743


상호 : 아이지 인터내셔날

전화번호 : 051-319-2877, [ 홈페이지 ]



링크공유

링크 :

관련 데이터시트

부품번호상세설명 및 기능제조사
BD9240F

Silicon Monolithic Integrated Circuit

Rohm
Rohm
BD9240F

Silicon Monolithic Integrated Circuit

Rohm
Rohm

DataSheet.kr    |   2019   |  연락처   |  링크모음   |   검색  |   사이트맵