|
|
PDF HCD-GTZ5 Data sheet ( Hoja de datos )
| Número de pieza | HCD-GTZ5 | |
| Descripción | COMPACT DISC RECEIVER SERVICE MANUAL | |
| Fabricantes | Sony | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de HCD-GTZ5 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
http://www.xiaoyu163.com
HCD-GTZ4/GTZ4i/GTZ5QQSE3RV7IC6E3M1AN5U1AL50
892498299
US Model
Ver. 1.1 2009.08
AEP Model
Australian Model
HCD-GTZ4i
E Model
HCD-GTZ4/GTZ5
• HCD-GTZ4 is the amplifier, USB, Disc player, tuner and
iPod section in MHC-GTZ4.
• HCD-GTZ4i is the amplifier, USB, Disc player, tuner and
iPod section in LBT-GTZ4i, MHC-GTZ4i.
• HCD-GTZ5 is the amplifier, USB, Disc player, tuner and
iPod section in MHC-GTZ5.
Photo: HCD-GTZ5
“WALKMAN” and “WALKMAN”
logo are registered trademarks of
Sony Corporation.
MICROVAULT is a trademark of
Sony Corporation.
Model Name Using Similar Mechanism
Mechanism Type
Optical Pick-up Block Name
NEW
CDM88B-DVBU101
KHM-313CAB
MPEG Layer-3 audio coding technol-
SPECIFICATIONS
ogy and patents licensed from Fraun-
hofer IIS and Thomson.
AUDIO POWER SPECIFICATION
Inputs
Windows Media is a registered trade-
mark of Microsoft Corporation in the
TEL 13942296513 QQ 376315150United States and/or other countries.
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
(HCD-GTZ4i: US model only)
With 6 ohm loads, both channels driven, from
120 Hz – 10 kHz; rated 110 watts per channel minimum RMS
PC (AUDIO IN) L/R:
Voltage 700 mV
impedance 47 kilohms
MIC: sensitivity 1 mV, impedance 10 kilohms
(USB) port: Type A
“Memory Stick” is a trademark of
Sony Corporation.
iPod is a trademark of Apple Inc., reg-
istered in the U.S. and other countries.
power, with no more than 0.7% total harmonic distortion from
250 miliwatts to rated output.
Amplifier section
HCD-GTZ5
The following are measured at
Mexican model:
AC 127 V, 60 Hz
Other models:
AC 120, 220, 240 V, 50/60 Hz
Outputs
PHONES: accepts headphones of 8 : or more
FRONT SPEAKER: accepts impedance of 6 :
SUBWOOFER: accepts impedance of 6 :
USB section
Supported bit rate
MP3 (MPEG 1 Audio Layer-3):
32 – 320 kbps, VBR
WMA: 48 – 192 kbps
AAC: 48 – 320 kbps
Front speaker
Sampling frequencies
Power output (rated): 110 W + 110 W
MP3 (MPEG 1 Audio Layer-3):
(at 6 :, 1 kHz, 1% THD)
32/44.1/48 kHz
RMS output power (reference):
WMA: 44.1 kHz
200 W + 200 W (per channel at 6 :, 1 kHz, 10% THD)
AAC: 44.1 kHz
Subwoofer
Transfer speed
RMS output power (reference): 200 W
(at 6 :, 100 Hz, 10% THD)
Full-Speed
Supported USB device
HCD-GTZ4i (US model)
Mass Storage Class
Maximum current
The following are measured at AC 120 V 60 Hz
Front speaker
RMS output power (reference):
:: SHUFKDQQHODWN+]7+'
Subwoofer
RMS output power (reference): 180 W
DW+]7+'
500 mA
Disc player section
System
Compact disc and digital audio system
Laser Diode Properties
Emission Duration: Continuous
Laser Output*: Less than 44.6 PW
HCD-GTZ4 / GTZ4i
(AEP, Australian, Argentina models)
The following are measured at
European model:
AC 230 V, 50 Hz
Other models:
AC 120, 220, 240 V, 50/60 Hz
Front speaker
Power output (rated): 90 W + 90 W
(at 6 :, 1 kHz, 1% THD)
RMS output power (reference):
155 W + 155 W (per channel at 6 :, 1 kHz, 10% THD)
* This output is the value measurement at a distance of
200 mm from the objective lens surface on the Optical
Pick-up Block with 7 mm aperture.
Frequency response
20 Hz – 20 kHz
Signal-to-noise ratio
More than 90 dB
Dynamic range
More than 88 dB
Tuner section
FM stereo, FM/AM superheterodyne tuner
Subwoofer
RMS output power (reference): 150 W
(at 6 :, 100 Hz, 10% THD)
FM tuner section
Tuning range:
892498299North American model:
87.5 – 108.0 MHz (100 kHz step)
Other models:
87.5 – 108.0 MHz (50 kHz step)
Antenna: FM lead antenna
Antenna terminals: 75 ohms unbalanced
Intermediate frequency: 10.7 MHz
AM tuner section
Tuning range
Pan American and Oceanian models:
530 – 1,710 kHz (with 10 kHz tuning interval)
531 – 1,710 kHz (with 9 kHz tuning interval)
European models:
531 – 1,602 kHz (with 9 kHz tuning interval)
Other models:
530 – 1,610 kHz (with 10 kHz tuning interval)
531 – 1,602 kHz (with 9 kHz tuning interval)
Antenna: AM loop antenna, external antenna terminal
Intermediate frequency: 450 kHz
iPod section
DC5V 500mA MAX
General
Power requirements
North American model: AC 120 V, 60 Hz
European models: AC 230 V, 50/60 Hz
Oceanian model: AC 230 – 240 V, 50/60 Hz
Mexican model: AC 127 V, 60 Hz
Argentine model: AC 220 V, 50/60 Hz
Other models: AC 120, 220 or 230 – 240 V, 50/60 Hz,
Adjustable with voltage selector
Power consumption
MHC-GTZ5: 250 W
HCD-GTZ4i (American model): 240W
MHC-GTZ4 / GTZ4i (Other models): 300 W
Dimensions (w/h/d) (excl. speakers)
Approx. 231 × 361 × 430.5 mm
(9 1/8 × 14 1/4 × 17 1/4 inch)
Mass (excl. speakers)
HCD-GTZ5 / GTZ4 / GTZ4i:
10.0 kg (22 lb 1 oz)
Design and specifications are subject to change without notice.
6WDQGE\SRZHUFRQVXPSWLRQ :
+DORJHQDWHGIODPHUHWDUGDQWVDUHQRWXVHGLQWKHFHUWDLQ
printed wiring boards.
www x aoy u163 com. i9-889-503-02 Sony Corporation
COMPACT DISC RECEIVER
.
2009H05-1
Audio&Video Business Group
© 2009.08
Published by Sony Techno Create Corporation
http://www.xiaoyu163.com
1 page  
http://www.xiaoyu163.com
HCD-GTZ4/GTZ4i/GTZ5
QQ 3763151502-3. TOP CASE
3 two claws
892498299
2 Lift up the back
side of top case.
1 screw
(BVTP3 u 8)
4 top case
TEL 139422965132-4. FRONT PANEL BLOCK
QQ 376315150 892498299
5 wire (flat type) (11 core)
(CN403)
8 two screws
(BVTP3 u 8)
4 wire (flat type) (27 core)
(CN405)
9 two harness
qs front panel block
0 screw
(BVTP3 u 10)
state of opening the CD tray
3 panel loading
www.
qa five screws
(BVTP3 × 8)
2 Pull the
tray by hand.
6 connector
(CN470)
7 connector
0 screw
(CN1501)
(BVTP3 × 10)
xiaoyu163.
lever
1 Turn a gear by
a driver till a lever
rises up to the
position of the figure.
gear
com
http://www.xiaoyu163.com
5
5 Page 
http://www.xiaoyu163.com
HCD-GTZ4/GTZ4i/GTZ5
TUNER STEP CHANGE
QQ 376315150(ExceptAEP model)
892498299VACS DISPLAY
This mode is used to check the VACS level.
The step interval of AM channels can be toggled between 9 kHz
Procedure:
and 10 kHz. This mode is not available for AEP model.
1. Press [?/1 STANDBY] button to turn on the system.
Procedure:
2. Press [ERASE], [x] and [ENTER] buttons simultaneously.
1. Press [?/1 STANDBY] button to turn on the system.
2. Press [TUNER/BAND] button repeatedly to select the “AM”.
3. The fluorescent indicator tube displays “VACSx”. “x” repre-
sents Conventional VACS level (Triggered by signal level).
3. Press [?/1 STANDBY] button to turn off the system.
4. To release from this mode, do the step 2 again.
4. Press [ENTER] and [?/1 STANDBY] buttons simultaneous-
ly. The system turns on automatically. The message “AM 9K
METER SWITCH TOUCH COUNT DISPLAY
STEP” or “AM 10K STEP” appears on the fluorescent indica-
This mode is used to display the total count of meter pointer touch
tor tube and thus the channel step is changed.
initial switch and max switch.
Procedure:
CD SHIP MODE (WITH MEMORY CLEAR)
1. Press [?/1 STANDBY] button to turn on the system.
This mode moves the optical pick-up to the position durable to
2. Press [x], [ENTER] and [DISPLAY] buttons simultaneously.
vibration and clears all data including preset data stored in the EE-
3. The fluorescent indicator tube displays “IxxxxxMyyyyy”.
PROM to initial conditions during the next AC-In. Use this mode
“I” represents the Initial Switch touch.
when returning the set to the customer after repair.
“xxxxx” represents the total count of Initial Switch touch.
Procedure:
(Maximum Value of “xxxxx” = 65535)
1. Press [?/1 STANDBY] button to turn on the system.
2. Press [CD] button to select CD function.
“M” represents the Max Switch touch.
“yyyyy” represents the total count of Max Switch touch.
3. Press [x], [DISC 1] and [?/1 STANDBY] buttons simultane-
ously. The system turns off automatically.
(Maximum Value of “yyyyy” = 65535)
4. To release from this mode, do the step 2 again. The fluorescent
4. After the “STANDBY” blinking display finishes, a message
indicator tube displays “MODE OUT”.
“MECHA LOCK” is displayed on the fluorescent indicator
tube and the CD ship mode is set.
METER TEST MODE
5. Unplug the power supply cable.
This mode is used to check the meter device.
Procedure:
CD SHIP MODE (WITHOUT MEMORY CLEAR)
1. Press [?/1 STANDBY] button to turn on the system.
This mode moves the optical pick-up to the position durable to
2. Press [x], [ENTER] and [METER MODE] buttons simulta-
vibration. Use this mode when returning the set to the customer
after repair.
TEL 13942296513 QQ 376315150 892498299Procedure:
neously. The fluorescent indicator tube displays “TST MODE
IN”.
3. Meter Backlight LEDs, Meter Pointer LEDs, Power Illumina-
1. Press [?/1 STANDBY] button to turn on the system.
2. Press [CD] button to select CD function.
tor LEDs and fluorescent indicator tube are lighted up.
4. When you want to perform count total step from Initial Switch
3. Press [DISC SKIP/EX-CHANGE] and [?/1 STANDBY] but-
tons simultaneously. The system turns off automatically.
to Max Switch operation mode, press [TUNING + > M]
button. The meter pointer will move from Initial Switch to
4. After the “STANDBY” blinking display finishes, a message
“MECHA LOCK” is displayed on the fluorescent indicator
tube and the CD ship mode is set.
Max Switch and finally move back to the middle position. The
total step count information appears on the fluorescent indica-
tor tube. “xxx STP yy” is shown.
5. Unplug the power supply cable.
“xxx” represents the total step.
(Value of “xxx” should between 430 steps to 470 steps)
CD TRAY LOCK MODE
This mode let you lock the disc tray. When this mode is activat-
ed, the disc tray will not open when [Z OPEN/CLOSE] button
or [DISC SKIP/EX-CHANGE] button is pressed. The message
“LOCKED” will be displayed on the fluorescent indicator tube.
Procedure:
1. Press [?/1 STANDBY] button to turn on the system.
2. Press [CD] button to select CD function.
3. Press [x] and [Z OPEN/CLOSE] buttons simultaneously and
hold down until “LOCKED” or “UNLOCKED” displayed on
the fluorescent indicator tube (around 5 seconds).
“yy” represents the status of total step count.
(If total step between 430 steps to 470 steps, “yy” is OK, Else
“yy” is NG)
5. When you want to perform count total step from Max Switch
to Initial Switch operation mode, press [TUNING – . m]
button. The meter pointer will move from Max Switch to Ini-
tial Switch and finally move back to the middle position. The
total step count information appears on the fluorescent indica-
tor tube. “xxx STP yy” is shown.
“xxx” represents the total step.
(Value of “xxx” should between 430 steps to 470 steps)
“yy” represents the status of total step count.
FACTORY PRESET
This mode is use to load all the factory use preset frequencies
into FM 1-FM 20 and AM 1-AM 10. Originally, frequency of FM
1-FM 20 and AM 1-AM10 are set to the minimum frequency.
(If total step between 430 steps to 470 steps, “yy” is OK, else
“yy” is NG).
6. To release from this mode, do the step 2 again. The fluorescent
indicator tube displays “TST MODE OUT”.
Procedure:
1. Press [?/1 STANDBY] button to turn on the system.
2. Press [SURROUND], [x] and [DISC 1] buttons simultane-
ously and the message “FACTORY” appears on the fluores-
cent indicator tube. The function is changed to TUNER auto-
www. xiaoyu163.matically.
com
http://www.xiaoyu163.com
11
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet HCD-GTZ5.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| HCD-GTZ4 | COMPACT DISC RECEIVER SERVICE MANUAL | Sony |
| HCD-GTZ4i | COMPACT DISC RECEIVER SERVICE MANUAL | Sony |
| HCD-GTZ5 | COMPACT DISC RECEIVER SERVICE MANUAL | Sony |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |