Datasheet.kr   

AT89LP51RC2 PDF 데이터시트 : 부품 기능 및 핀배열

부품번호 AT89LP51RC2
기능 8-bit Flash Microcontroller
제조업체 ATMEL
로고 ATMEL 로고 


전체 30 페이지

		

No Preview Available !

AT89LP51RC2 데이터시트, 핀배열, 회로
Features
8-bit Microcontroller Compatible with 8051 Products
Enhanced 8051 Architecture
– Single Clock Cycle per Byte Fetch
– 12 Clock per Machine Cycle Compatibility Mode
– Up to 20 MIPS Throughput at 20 MHz Clock Frequency
– Fully Static Operation: 0 Hz to 20 MHz
– On-chip 2-cycle Hardware Multiplier
– 16x16 Multiply–Accumulate Unit
– 256 x 8 Internal RAM
– On-chip 1152 Bytes Expanded RAM (ERAM)
• Software Selectable Size (0, 256, 512, 768, 1024 or 1152 Bytes)
– Dual Data Pointers
– 4-level Interrupt Priority
Nonvolatile Program and Data Memory
– 24KB/32KB of In-System Programmable (ISP) Flash Program Memory
– 512-byte User Signature Array
– Endurance: 10,000 Write/Erase Cycles
– Serial Interface for Program Downloading
– 2KB Boot ROM Contains Low Level Flash Programming Routines and a Default
Serial Bootloader
Peripheral Features
– Three 16-bit Enhanced Timer/Counters
– Seven 8-bit PWM Outputs
– 16-bit Programmable Counter Array
• High Speed Output, Compare/Capture
• Pulse Width Modulation, Watchdog Timer Capabilities
– Enhanced UART with Automatic Address Recognition and Framing
Error Detection
– Enhanced Master/Slave SPI with Double-buffered Send/Receive
Two Wire Interface 400K bit/s
– Programmable Watchdog Timer with Software Reset
– 8 General-purpose Interrupt and Keyboard Interface Pins
Special Microcontroller Features
– Dual Oscillator Support: Crystal, 32 kHz Crystal, 8 MHz Internal (AT89LP51IC2)
– Two-wire On-Chip Debug Interface
– Brown-out Detection and Power-on Reset with Power-off Flag
– Selectable Polarity External Reset Pin
– Low Power Idle and Power-down Modes
– Interrupt Recovery from Power-down Mode
– 8-bit Clock Prescaler
I/O and Packages
– Up to 40 Programmable I/O Lines
– Green (Pb/Halide-free) PLCC44, VQFP44, QFN44. PDIP40
– Configurable I/O Modes
• Quasi-bidirectional (80C51 Style), Input-only (Tristate)
• Push-pull CMOS Output, Open-drain
Operating Conditions
– 2.4V to 5.5V VCC Voltage Range
– -40° C to 85°C Temperature Range
– 0 to 20 MHz @ 2.4V–5.5V (Single-cycle)
8-bit Flash
Microcontroller
with 24K/32K
bytes Program
Memory
AT89LP51RB2
AT89LP51RC2
AT89LP51IC2
Preliminary
3722A–MICRO–10/11




AT89LP51RC2 pdf, 반도체, 판매, 대치품
1.5 Pin Description
Table 1-1. Atmel AT89LP51RB2/RC2/IC2 Pin Description
Pin Number
VQFP
VQFN PLCC
(1)
PDIP
Symbol
Type Description
I/O P1.5: User-configurable I/O Port 1 bit 5.
I/O MISO: SPI master-in/slave-out. When configured as master, this pin is an input. When
configured as slave, this pin is an output.
1
7
6
P1.5
I/O MOSI: SPI master-out/slave-in (Remap mode). When configured as master, this pin is an output.
When configured as slave, this pin is an input. During In-System Programming, this pin is an
input.
I/O CEX2: Capture/Compare external I/O for PCA module 2.
I/O P1.6: User-configurable I/O Port 1 bit 6.
I/O SCK: SPI Clock. When configured as master, this pin is an output. When configured as slave,
this pin is an input.
2
8
7
P1.6
I/O MISO: SPI master-in/slave-out (Remap mode). When configured as master, this pin is an input.
When configured as slave, this pin is an output. During In-System Programming, this pin is an
output.
I/O CEX3: Capture/Compare external I/O for PCA module 3.
I/O P1.7: User-configurable I/O Port 1 bit 7.
I/O MOSI: SPI master-out/slave-in. When configured as master, this pin is an output. When
3
9
8
P1.7
configured as slave, this pin is an input.
I/O SCK: SPI Clock (Remap mode). When configured as master, this pin is an output. When
configured as slave, this pin is an input. During In-System Programming, this pin is an input.
I/O CEX4: Capture/Compare external I/O for PCA module 4.
I/O RST: External Reset input (Reset polarity depends on POL pin. See “External Reset” on page
4 10 9 RST
53.). The RST pin can output a pulse when the internal Watchdog reset or POR is active.
I DCL: Serial Debug Clock input for On-Chip Debug Interface when OCD is enabled.
5
11
10
P3.0
I/O P3.0: User-configurable I/O Port 3 bit 0.
I RXD: Serial Port Receiver Input.
6 12
P4.1
I/O P4.1: User-configurable I/O Port 4bit 1.
I/O SDA: TWI bidirectional Serial Data line.
7
13
11
P3.1
I/O P3.1: User-configurable I/O Port 3 bit 1.
O TXD: Serial Port Transmitter Output.
8
14
12
P3.2
I/O P3.2: User-configurable I/O Port 3 bit 2.
I INT0: External Interrupt 0 Input or Timer 0 Gate Input.
9
15
13
P3.3
I/O P3.3: User-configurable I/O Port 3 bit 3.
I INT1: External Interrupt 1 Input or Timer 1 Gate Input
10
16
14
P3.4
I/O P3.4: User-configurable I/O Port 3 bit 4.
I/O T1: Timer/Counter 0 External input or output.
11
17
15
P3.5
I/O P3.5: User-configurable I/O Port 3 bit 5.
I/O T1: Timer/Counter 1 External input or output.
12
18
16
P3.6
I/O P3.6: User-configurable I/O Port 3 bit 6.
O WR: External memory interface Write Strobe (active-low).
13
19
17
P3.7
I/O P3.7: User-configurable I/O Port 3 bit 7.
O RD: External memory interface Read Strobe (active-low).
I/O P4.7: User-configurable I/O Port 4 bit 7.
14 20 18
P4.7
O XTAL2A: Output from inverting oscillator amplifier A. It may be used as a port pin if the internal
RC oscillator or external clock is selected as the clock source A.
I/O P4.6: User-configurable I/O Port 4 bit 6.
15 21 19 P4.6
I XTAL1A: Input to the inverting oscillator amplifier A and internal clock generation circuits. It may
be used as a port pin if the internal RC oscillator is selected as the clock source A.
4 AT89LP51RB2/RC2/IC2 Preliminary
3722A–MICRO–10/11

4페이지










AT89LP51RC2 전자부품, 판매, 대치품
AT89LP51RB2/RC2/IC2 Preliminary
AT89LP51RB2/RC2/IC2 also includes a compatibility mode that will enable classic 12 clock per
machine cycle operation for true timing compatibility with the Atmel AT89C51RB2/RC2/IC2.
The AT89LP51RB2/RC2/IC2 retains all of the standard features of the AT89C51RB2/RC2/IC2,
including: 24KB/32KB of In-System Programmable Flash program memory, 256 bytes of RAM,
1152 bytes of expanded RAM, up to 40 I/O lines, three 16-bit timer/counters, a Programmable
Counter Array, a programmable hardware watchdog timer, a keyboard interface, a full-duplex
enhanced serial port, a serial peripheral interface (SPI), on-chip crystal oscillator, and a four-
level, ten-vector interrupt system. A block diagram is shown in Figure 2-1.
In addition, the Atmel® AT89LP51RB2/RC2/IC2 provides a Two-Wire Interface (TWI) for up to
400KB/s serial transfer; a 10-bit, 8-channel Analog-to-Digital Converter (ADC) with temperature
sensor and digital-to-analog (DAC) mode; two analog comparators; and an 8MHz internal
oscillator.
Some standard features on the AT89LP51RB2/RC2/IC2 are enhanced with new modes or oper-
ations. Mode 0 of Timer 0 or Timer 1 acts as a variable 9–16 bit timer/counter and Mode 1 acts
as a 16-bit auto-reload timer/counter. In addition, each timer/counter may independently drive an
8-bit precision pulse width modulation output. Mode 0 (synchronous mode) of the serial port
allows flexibility in the phase/polarity relationship between clock and data.
The I/O ports of the AT89LP51RB2/RC2/IC2 can be independently configured in one of four
operating modes. In quasi-bidirectional mode, the ports operate as in the classic 8051. In input-
only mode, the ports are tristated. Push-pull output mode provides full CMOS drivers and open-
drain mode provides just a pull-down. Unlike other 8051s, this allows Port 0 to operate with on-
chip pull-ups if desired.
The AT89LP51RB2/RC2/IC2 includes an On-Chip Debug (OCD) interface that allows read-mod-
ify-write capabilities of the system state and program flow control, and programming of the
internal memories. The on-chip Flash may also be programmed through the UART-based boot-
loader or the SPI-based In-System programming interface (ISP).
The TWI and OCD features are not available on the PDIP package. The AT89LP51IC2 is also
not available in the PDIP.
The features of the AT89LP51RB2/RC2/IC2 make it a powerful choice for applications that need
pulse width modulation, high speed I/O, and counting capabilities such as alarms, motor control,
corded phones, and smart card readers.
3722A–MICRO–10/11
7

7페이지



구       성총 30 페이지
다운로드[ AT89LP51RC2.PDF 데이터시트 ]
구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

전력 반도체 판매 ( IGBT, TR 모듈, SCR, 다이오드 모듈 )

휴대전화 : 010-3582-2743


상호 : 아이지 인터내셔날

전화번호 : 051-319-2877, [ 홈페이지 ]



링크공유

링크 :

관련 데이터시트

부품번호상세설명 및 기능제조사
AT89LP51RC2

8-bit Flash Microcontroller

ATMEL
ATMEL

DataSheet.kr    |   2019   |  연락처   |  링크모음   |   검색  |   사이트맵