Datasheet.kr   

OB3613Y 데이터시트 PDF




On-Bright에서 제조한 전자 부품 OB3613Y은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


 

PDF 형식의 OB3613Y 자료 제공

부품번호 OB3613Y 기능
기능 High PF Non-Isolated Buck LED Lighting Power Switch
제조업체 On-Bright
로고 On-Bright 로고


OB3613Y 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.



전체 9 페이지수

미리보기를 사용할 수 없습니다

OB3613Y 데이터시트, 핀배열, 회로
OB3613Y
High PF Non-Isolated Buck LED Lighting Power Switch
GENERAL DESCRIPTION
OB3613Y is a high power factor, highly integrated
buck regulator with advanced features to provide
high efficiency control and high precision constant
current output for LED lighting applications.
OB3613Y integrates a 1.5A MOSFET to decrease
physical volume. The proprietary CC control
scheme is used and the system can achieve high
power factor with constant on-time control
scheme.
OB3613Y offers comprehensive protection
coverage with auto-recovery features including
LED open loop protection, LED short circuit
protection, cycle-by-cycle current limiting, built-in
leading edge blanking, VDD under voltage lockout
(UVLO), etc.
OB3613Y is offered in SOP8 package.
TYPICAL APPLICATION
FEATURES
Buck topology with high power factor
Integrated 1.5A 600V MOSFET
High precision constant current regulation at
universal AC input
Low system cost and high efficiency
Quasi-Resonant operation
Programmable CC regulation
LED short circuit protection
LED open loop protection
Cycle-by-cycle current limiting
Built-in leading edge blanking (LEB)
VDD under voltage lockout with hysteresis
VDD over voltage protection
Over temperature protection (OTP)
APPLICATIONS
LED lighting
Figure1: OB3613Y Typical Application Schematic
Output Power Table
Product
Condition
90Vac~264Vac Input
220Vac±20% Input
OB3613Y
IOUT0.23A
7.5W
11.2W
Note: Maximum practical continuous power in an open frame design with sufficient drain pattern as a heat sink, at 50ambient
and 60temperature rise. Higher output power is possible with extra added heat sink or air circulation to reduce thermal resistance.
©On-Bright Electronics
Confidential
-1-
Preliminary Datasheet
OB_DOC_DS_3613Y00




OB3613Y pdf, 반도체, 판매, 대치품
Marking Information
OB3613Y
High PF Non-Isolated Buck LED Lighting Power Switch
TERMINAL ASSIGNMENTS
Pin Num Pin Name
1 VDD
2 FB
3 COMP
4 CS
5,6 DRAIN
7 GND
8 GND
I/O Description
P Power supply Input.
I
The voltage feedback from auxiliary winding. Connected to resistor
divider from auxiliary winding reflecting output voltage.
O
Loop compensation pin. A capacitor is connected between COMP and
GND.
I Current sensing terminal.
I MOSFET Drain Terminal
P Power Ground, suggest to be left floating with no pad in PCB layout.
P Power Ground
©On-Bright Electronics
Confidential
-4-
Preliminary Datasheet
OB_DOC_DS_3613Y00

4페이지










OB3613Y 전자부품, 판매, 대치품
OB3613Y
High PF Non-Isolated Buck LED Lighting Power Switch
OPERATION DESCRIPTION
OB3613Y is a high power factor, highly integrated
buck regulator with advanced features to provide
high efficiency control and high precision constant
current output for LED lighting applications. It
integrates a 1.5A MOSFET and provides LED
open/short protection.
Start up Control
Low start-up current is designed in OB3613Y so
that VDD could be charged up above UVLO
threshold with small charging current. A large
value startup resistor can therefore be used to
minimize the power loss in application.
The capacitor at COMP pin is pulled up quickly
during starting up until its voltage reaches 1.2V.
Then the error amplifier charges the COMP pin
capacitor with a transconductance of about 500uS
(typical), and the Gate drives external power
MOSFET at minimum frequency for low power
dissipation. At the startup, the threshold voltage of
OCP is set at 0.5V (typical). When the voltage at
FB pin reaches 0.45V (typical), the threshold
voltage of OCP is increased to 1V (typical). When
the voltage at FB pin increases and reaches 1.2V
(typical), the transconductance of error amplifier is
reduced to 50uS (typical).
LED Constant Current Regulation
OB3613Y uses the constant current control
method to accurately control the LED current. It
detects LED current and forces the average LED
current equals to the ratio of reference voltage to
resistance at CS pin as shown in the equation
below.
I LED
Vref
R CS
Rcs — The sensing resistor connected between
the MOSFET source and the GND pin of IC.
Vref — Internal reference voltage.
PFC
The duration of the turn on period ton is generated
by comparing an internal fixed saw-tooth wave
with the voltage on the COMP pin. During steady
state operation, the voltage on the COMP pin
Vcomp is slowly varying due to a large external
capacitor connected at the COMP pin, therefore
the turn on time ton is constant. In a buck topology,
constant turn on time.
Current Sensing and Leading Edge
Blanking
Cycle-by-Cycle current limiting (OCP) is offered in
OB3613Y. The switching current is detected by a
sense resistor connected between the CS pin and
GND. An internal leading edge blanking circuit
chops off the sense voltage spike at initial
MOSFET on state due to wheel diode reverse
recovery so that the external RC filter is no longer
required. The current limit comparator is disabled
at this blanking time and thus the external
MOSFET cannot be turned off during this blanking
time.
LED Open/Output OVP Protection
When LED string is open, an output over-voltage
condition is monitored independently by the
voltage at pin FB. During normal operation, when
the voltage at FB pin exceeds a threshold of
approximately 3.5V (typical), the over-voltage
protection function is activated and the GATE is
turned off immediately until VDD voltage drops
below UVLO (ON), and the device enters power
on startup sequence thereafter.
VDD Over Voltage Protection
VDD is supplied from the BUCK output as shown
in the typical application diagram. When VDD is
higher than 35V (typical), VDD OVP protection is
triggered and OB3613Y is shut down, and the
device enters power on startup sequence
thereafter.
LED Short Circuit Protection
When LED string is short, the voltage at FB pin
drops to below a threshold of approximately 0.45V
(typical), the IC will work at minimum frequency
and the threshold voltage of OCP is reduced to
0.5V (typical). The power dissipation is greatly
reduced in this way. When the VDD voltage drops
to UVLO(ON), the device enters power on startup
sequence thereafter.
©On-Bright Electronics
Confidential
-7-
Preliminary Datasheet
OB_DOC_DS_3613Y00

7페이지


구       성 총 9 페이지수
다운로드[ OB3613Y.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
OB3613

High PF Non-Isolated Buck LED Lighting Controller

On-Bright
On-Bright
OB3613MCP

High PF Non-Isolated Buck LED Lighting Power Switch

On-Bright
On-Bright

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵