|
|
|
부품번호 | NCV7718B 기능 |
|
|
기능 | Hex Half-Bridge Driver | ||
제조업체 | ON Semiconductor | ||
로고 | |||
전체 27 페이지수
NCV7718B
Hex Half-Bridge Driver
The NCV7718B is a Hex Half−Bridge Driver with protection
features designed specifically for automotive and industrial motion
control applications. The NCV7718B has independent controls and
diagnostics. The device can be operated in forward, reverse, brake,
and high impedance states. The drivers are controlled via a 16 bit SPI
interface and are daisy chain compatible.
Features
• Low Quiescent Current Sleep Mode
• High−Side and Low−Side Drivers Connected in a Half−Bridge
Configuration
• Integrated Freewheeling Protection (LS and HS)
• 0.55 A Peak Current
• RDS(on) = 1 W (typ)
• 5 MHz SPI Control
• Compliance with 5 V and 3. 3 V Systems
• Undervoltage and Overvoltage Lockout
• Discriminated Fault Reporting
• Overcurrent Protection
• Overtemperature Protection
• Under Load Detection (LS)
• Daisy Chain Compatible with Multiple of 8 bit Devices
• 16−Bit Frame Detection
• Exposed Pad Package
• NCV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q100
Qualified and PPAP Capable
• These are Pb−Free Devices
Typical Applications
• Automotive
• Industrial
• DC Motor Management for HVAC Application
http://onsemi.com
MARKING
DIAGRAM
SSOP24 NB EP
CASE 940AK
NCV7718B
AWLYYWWG
NCV7718B = Specific Device Code
A = Assembly Location
WL = Wafer Lot
YY = Year
WW = Work Week
G = Pb−Free Package
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 25 of this data sheet.
© Semiconductor Components Industries, LLC, 2014
August, 2014 − Rev. 0
1
Publication Order Number:
NCV7718B/D
NCV7718B
GND
OUT1
OUT5
NC
SI
VCC
SO
EN
NC
OUT6
OUT4
GND
1
2
3
4
5
6
7
8
9
10
11
12
24 GND
23 OUT2
22 NC
21 VS1
20 SCLK
19 CSB
18 RESERVED
17 RESERVED
16 VS2
15 NC
14 OUT3
13 GND
Figure 3. Pinout − SSOP24 (Top View)
PACKAGE DESCRIPTION The pin−out for the Hex Half−Bridge in SSOP24 package is shown in the table below.
Pin #
SSOP24
Symbol
Description
1
GND
Ground. Shorted to pin 24 internally.
2
OUT1
Half Bridge Output 1
3
OUT5
Half Bridge Output 5
4 NC No Connection. This pin should be isolated from any traces or via on the PCB board.
5 SI Serial Input. 16 bit serial communications input. 3.3 V/5 V (TTL) Compatible. Internally pulled down.
6
VCC
Power supply input for Logic.
7 SO Serial Output. 16 bit serial communications output. 3.3 V/5 V Complaint
8 EN Enable. Input high wakes the IC up from a sleep mode. 3.3 V/5 V (TTL) Compatible. Internally pulled down.
9 NC No Connection. This pin should be isolated from any traces or via on the PCB board.
10
OUT6
Half Bridge Output 6
11
OUT4
Half Bridge Output 4
12
GND
Ground. Shorted to pin 13 internally.
13
GND
Ground. Shorted to pin 12 internally.
14
OUT3
Half Bridge Output 3
15 NC No Connection. This pin should be isolated from any traces or via on the PCB board.
16 VS2 Voltage Power Supply input for the Drivers 3, 4 and 6. This pin must be connected to VS1 externally.
17 Reserved Reserved for internal use. This pin must be grounded.
18 Reserved Reserved for internal use. This pin must be grounded.
19
CSB
Chip Select Bar. Active low serial port operation. 3.3V/5V (TTL) Compatible. Internally pulled up.
20
SCLK
Serial Clock. Clock input for use with SPI communication. 3.3 V/5 V (TTL) Compatible. Internally pulled
down.
21 VS1 Voltage Power Supply input for the Drivers 1, 2 and 5, all the pre−drivers and the charge pump. This pin
must be connected to VS2 externally.
22 NC No Connection. This pin should be isolated from any traces or via on the PCB board.
23
OUT2
Half Bridge Output 2
24
GND
Ground. Shorted to pin 1 internally.
EPAD
Exposed
Pad
Connect to GND or leave unconnected.
http://onsemi.com
4
4페이지 NCV7718B
ELECTRICAL CHARACTERISTICS (−40°C < TJ < 150°C, 5.5 V < VSx < 40 V, 3.15 V < VCC < 5.25 V, EN = VCC, unless otherwise
specified)
Characteristic
Symbol
Conditions
Min Typ Max Unit
BODY DIODE
Power Transistor Body Diode
Forward Voltage
VbdFwd
If = 500 mA
− 0.9 1.3 V
LOGIC INPUTS (EN, SI, SCLK, CSB)
Input Threshold
High
Low
Input Hysteresis (SI, SCLK,
CSB)
VthInH
VthInL
VthInHys
V
2.0 −
−
− − 0.6
50 150 300 mV
Enable Hysteresis
Input Pull−down Resistance
(EN, SI, SCLK)
VthENHys
Rpdx
EN = SI = SCLK = VCC
150 400 800 mV
50 125 200 kW
Input Pull−up Resistance
(CSB)
RpuCSB CSB = 0 V
50 125 250 kW
Input Capacitance
LOGIC OUTPUT (SO)
Cinx
Not ATE tested
− −− 15 pF
Output High
VsoH
ISOURCE = −1 mA
VCC –
−
−
V
0.6
Output Low
Tri−state Leakage
Tri−state Output Capacitance
VsoL
ItriStLkg
ItriStCout
ISINK = 1.6 mA
CSB = 5 V
CSB = VCC, 0 V < VCC < 5.25 V
Not ATE tested
− − 0.4 V
−5 −
5 mA
− − 15 pF
http://onsemi.com
7
7페이지 | |||
구 성 | 총 27 페이지수 | ||
다운로드 | [ NCV7718B.PDF 데이터시트 ] |
당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는 |
구매 문의 | 일반 IC 문의 : 샘플 및 소량 구매 ----------------------------------------------------------------------- IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한 광범위한 전력 반도체를 판매합니다. 전력 반도체 전문업체 상호 : 아이지 인터내셔날 사이트 방문 : [ 홈페이지 ] [ 블로그 1 ] [ 블로그 2 ] |
부품번호 | 상세설명 및 기능 | 제조사 |
NCV7718 | Hex Half-Bridge Driver | ON Semiconductor |
NCV7718B | Hex Half-Bridge Driver | ON Semiconductor |
DataSheet.kr | 2020 | 연락처 | 링크모음 | 검색 | 사이트맵 |