Datasheet.kr   

MS75089D 데이터시트 PDF




ETC에서 제조한 전자 부품 MS75089D은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


PDF 형식의 MS75089D 자료 제공

부품번호 MS75089D 기능
기능 Coil
제조업체 ETC
로고 ETC 로고


MS75089D 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.



전체 4 페이지수

미리보기를 사용할 수 없습니다

MS75089D 데이터시트, 핀배열, 회로
INCH-POUND
MS75089D
7 September 2007
SUPERSEDING
MS75089C
3 March 1999
MILITARY SPECIFICATION SHEET
COILS, RADIO FREQUENCY, MOLDED, FIXED, MICRO-MINIATURE,
MAGNETICALLY SHIELDED, (FERRITE CORE – FERRITE SLEEVE),
TYPES LT10K217 TO LT10K263, INCLUSIVE
Inactive for new design, after 4 September 1985.
For new design, use MIL-PRF-39010/3.
This specification is approved for use by all Depart-
ments and Agencies of the Department of Defense.
The requirements for acquiring the products described
herein shall consist of this specification and MIL-PRF-15305.
Dash numbers –01 through -47
Dash numbers –48 through -94
LTR
Dimensions in inches with metric
Equivalents (mm) in parentheses
Dimensions in inches with metric
Equivalents (mm) in parentheses
Minimum
Maximum
Minimum
Maximum
A
.152 (3.86)
.172 (4.37)
.152 (3.86)
.197 (5.00)
B
.390 (9.91)
.430 (10.92)
.390 (9.91)
.447 (11.35)
C
1.250 (31.75) 1.626 (41.30)
1.250 (31.75)
1.626 (41.30)
D
.023 (0.58)
.027 (0.69)
.023 (0.58)
.027 (0.69)
NOTES:
1. Dimensions are in inches.
2. Metric equivalents are given for general information only.
3. These coils are intended to be supported by their bodies.
4. Solderable/weldable lead wire, number 22 AWG.
FIGURE 1. Dimensions and configuration.
AMSC N/A
FSC 5950




MS75089D pdf, 반도체, 판매, 대치품
Inspection
group
Qualification
inspection
Group II
Group III
Group IV
Conformance
inspection group C
Subgroup I
Subgroup II
Subgroup III
MS75089D
TABLE II. Electrical characteristics (final).
Allowable variation from
Initial measurement
Inductance
(percent)
DC resistance
Allowable percent from specified minimum
value in electrical characteristics
(initial) table
Self-resonant
Q
frequency
±5 --- ---
±10 ±(5% +.001 ohm) -15
±5 ±(2% +.001 ohm) -5
-10
-20
-20
±5 --- ---
±5 ±(2% +.001 ohm) -5
±10 ±(4% +.001 ohm) -15
-10
-20
-20
Application notes:
1. After the overload test is performed, a period of 24 hours shall elapse prior to taking electrical characteristics
(final) measurements.
2. DC resistance shall be the last measurement taken in the electrical characteristics test sequence.
Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where
changes from the previous issue were made. This was done as a convenience only and the Government assumes
no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the
requirements of this document based on the entire content irrespective of the marginal notations and relationship to
the last previous issue.
Referenced documents.
MIL-PRF-15305
MIL-STD-202
Custodians:
Army – CR
Navy - EC
Air Force - 11
DLA – CC
Preparing activity:
DLA – CC
Project 5950-2007-041
Review activities:
Army – AR, CR4, MI
Navy – AS, MC, OS, SH
Air Force – 19
NOTE: The activities listed above were interested in this document as of the date of this document. Since
organizations and responsibilities can change, you should verify the currency of the information above using the
ASSIST Online database at http://assist.daps.dla.mil.
4

4페이지












구       성 총 4 페이지수
다운로드[ MS75089D.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
MS75089D

Coil

ETC
ETC

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵