Datasheet.kr   

FEDL9058E 데이터시트 PDF




LAPIS에서 제조한 전자 부품 FEDL9058E은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


PDF 형식의 FEDL9058E 자료 제공

부품번호 FEDL9058E 기능
기능 132-Channel LCD Driver
제조업체 LAPIS
로고 LAPIS 로고


FEDL9058E 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.



전체 30 페이지수

미리보기를 사용할 수 없습니다

FEDL9058E 데이터시트, 핀배열, 회로
LAPIS Semiconductor
FEDL9058E-01
Issue Date: April. 13, 2007
ML9058E
132-Channel LCD Driver with Built-in RAM for LCD Dot Matrix Displays
GENERAL DESCRIPTION
The ML9058E is an LSI for dot matrix graphic LCD devices carrying out bit map display. This LSI can drive a dot
matrix graphic LCD display panel under the control of an 8-bit microcomputer (hereinafter described MPU).
Since all the functions necessary for driving a bit map type LCD device are incorporated in a single chip, using the
ML9058E makes it possible to realize a bit map type dot matrix graphic LCD display system with only a few chips.
Since the bit map method in which one bit of display RAM data turns ON or OFF one dot in the display panel, it is
possible to carry out displays with a high degree of freedom such as Chinese character displays, etc. With one chip,
it is possible to construct a graphic display system with a maximum of 65 132 dots. The display can be expanded
further using two chips. However, the ML9058E is not used in a multiple chip configuration when a line reversal
drive is set.
The ML9058E is made using a CMOS process. Because it has a built-in RAM, low power consumption is one of
its features, and is therefore suitable for displays in battery-operated portable equipment.
The ML9058E has 65 common signal outputs and 132 segment signal outputs and one chip can drive a display of
up to 65 132 dots.
FEATURES
Direct display of the RAM data using the bit map method
Display RAM data “1” ... Dot is displayed
Display RAM data “0” ... Dot is not displayed (during forward display)
Display RAM capacity
65 132 = 8580 bits
LCD Drive circuits
65 common outputs, 132 segment outputs
MPU interface: Can select an 8-bit parallel or serial interface
Built-in voltage multiplier circuit for the LCD drive power supply
Built-in LCD drive voltage adjustment circuit
Built-in LCD drive bias generator circuit
Can select frame reversal drive or line reversal drive by command
Built-in oscillator circuit (Internal RC oscillator/external clock input)
A variety of commands
Read/write of display data, display ON/OFF, forward/reverse display, all dots ON/all dots OFF, set page
address, set display start address, etc.
Power supply voltage
Logic power supply: VDD-VSS = 3.7 V to 5.5 V
Voltage multiplier reference voltage: VIN-VSS = 3.7 V to 5.5 V
(2- to 4-time multiplier available)
LCD Drive voltage: VBI-VSS = 6.0 to 18 V
Package: Gold bump chip (Bump hardness: Low, DV)
: Gold bump chip (Bump hardness: High, CV)
This device is not resistant to radiation and light.
1/76




FEDL9058E pdf, 반도체, 판매, 대치품
LAPIS Semiconductor
FEDL9058E-01
ML9058E
Note 5:
Note 6:
When using an external power supply, follow the procedure for power application.
When applying external power to the VOUT pin only, apply VOUT after VDD.
When applying external power to the V1 pin only, apply V1 after VDD.
When applying external power to the V1 pin to V5 pin, apply V1 to V5 after VDD.
Note that the above (Note 4) must be satisfied including transient state at power application.
When using an external power supply, follow the procedure for power removal described
below.
When external power is in use for the VOUT pin only, remove VOUT after VDD.
When external power is in use for the V1 pin only, remove V1 after VDD.
When external power is in use for the V1 pin to V5 pin, remove V1 to V5 after VDD.
Note that the above (Note 4) must be satisfied including transient state at power removal.
4/76

4페이지










FEDL9058E 전자부품, 판매, 대치품
LAPIS Semiconductor
FEDL9058E-01
ML9058E
Operating current consumption value
(1) During display operation, internal power supply OFF (The current flowing through VDD with V1 to V5
externally applied when an external power supply is used, not including the current for the LCD drive)
Display mode Symbol
Condition
[VSS = 0 V, Tj = 25°C]
Rated value
Min Typ Max
Unit
All-white
IDD VDD = 5 V, V1- VSS = 11 V, no load — 16 45 A
VDD = 3.7 V, V1- VSS = 8 V, no load — 12 35
Checker pattern IDD VDD = 5 V, V1- VSS = 11 V, no load — 16 45 A
VDD = 3.7 V, V1- VSS = 8 V, no load — 12 35
(2) During display operation, internal power supply ON (Total of currents flowing through VDD and VIN)
[VSS = 0 V, Tj = 25°C]
Display
mode
Symbol
Condition
Rated value
Unit
Min Typ Max
All-white
IDDIN
Frame reversal,
VDD, VIN = 5 V, 3-time
voltage multiplication
V1 - VSS= 11 V, no load
Frame reversal,
VDD, VIN = 3.7 V, 4-time
voltage multiplication
V1 - VSS= 8 V, no load
16-line reversal,
VDD, VIN = 5 V, 3-time
voltage multiplication
— 100 170
— 110 190 A
— 100 170
V1 - VSS= 11 V, no load
Frame reversal,
VDD, VIN = 5 V, 3-time
voltage multiplication
— 120 205
Checker
pattern
IDDIN
V1 - VSS= 11 V, no load
Frame reversal,
VDD, VIN = 3.7 V, 4-time
voltage multiplication
— 130 220 A
V1 - VSS= 8 V, no load
16-line reversal,
VDD, VIN = 5 V, 3-time
voltage multiplication
— 120 205
V1 - VSS= 11 V, no load
Power save mode current consumption
Parameter
Sleep mode
Standby mode
Symbol
IDDS1
IDDS2
Condition
VDD = 3.7 V
VDD = 3.7 V
[VSS = 0 V, Tj = 25°C]
Rated value
Min Typ Max
Unit
— 0.3
5
A
— 9 15
7/76

7페이지


구       성 총 30 페이지수
다운로드[ FEDL9058E.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
FEDL9058E

132-Channel LCD Driver

LAPIS
LAPIS

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵