Datasheet.kr   

PL1084J3 데이터시트 PDF




Cystech Electonics에서 제조한 전자 부품 PL1084J3은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


 

PDF 형식의 PL1084J3 자료 제공

부품번호 PL1084J3 기능
기능 5A Low Dropout Positive Voltage Regulator
제조업체 Cystech Electonics
로고 Cystech Electonics 로고


PL1084J3 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.



전체 9 페이지수

미리보기를 사용할 수 없습니다

PL1084J3 데이터시트, 핀배열, 회로
Spec. No. : C512J3
CYStech Electronics Corp. Issued Date : 2007.07.04
Revised Date : 2014.12.29
Page No. : 1/9
5A Low Dropout Positive Voltage Regulator
PL1084J3
TO-252(DPAK)
Features
Maximum Dropout Voltage 1.5V at 5A Output Current.
Fast Transient Response.
Extremely Tight Line and Load Regulation.
Current Limiting and Thermal Protection.
Adjustable Output Voltage or Fixed 1.5V, 1.8V,2.5V,3.3V,5.0V.
Standard 3-Pin Power Packages.
Adj/Gnd Vout Vin
Description
The PL1084J3 is a low dropout three terminal regulator with 5A output current capability. The output voltage is adjustable
with the use of a resistor divider or fixed 1.5V, 1.8V, 2.5V, 3.3V, and 5.0V. Dropout voltage is guaranteed to be at maximum
of 1.5V with the maximum output current. Its low dropout voltage and fast transient response make it ideal for low voltage
microprocessor applications. Current limit and thermal protection provide protection against any overload condition that
would create excessive junction temperatures.
Applications
Mother Board I/O Power Supplies.
Microprocessor Power Supplies.
High Current Regulator.
Post Regulator for Switching Supply.
Typical Application Circuit
Vin=5V
C1
10μF
32
PL1084-Adj
VREF
1 ADJ
R1
125Ω
1%
R2
205Ω
1%
Vout=3.3V
C2
22μF
VOUT=VREF×(1+R2/R1)+IADJ×R2
C1 is required if device is far from filter
capacitance.
C2 minimum value required for stability.
Adjustable Voltage Regulator
Vin=5V
C1
10μF
3
PL1084-3.3
2
1
Vout=3.3V
C2
22μF
C1 is required if device is far from filter
capacitance.
C2 minimum value required for stability.
PL1084J3
Fixed Voltage Regulator
CYStek Product Specification




PL1084J3 pdf, 반도체, 판매, 대치품
Spec. No. : C512J3
CYStech Electronics Corp. Issued Date : 2007.07.04
Revised Date : 2014.12.29
Page No. : 4/9
Functional Description
Introduction
The PL1084 adjustable Low Dropout(LDO) regulator is a 3 terminal device that can easily be programmed with the
addition of two external resistors to any voltages within the range of 1.25V to 2.5V. The PL1084 only needs 1.5V
differential between Vin and Vout to maintain output regulation. In addition, the output voltage tolerances are also
extremely tight and they include the transient response as part of the specification. For example, Intel VRE
specification calls for a total of ±100mV including initial tolerance, load regulation and 0 to 5A load step. The
PL1084 is specifically designed to meet the fast current transient needs as well as providing an accurate initial voltage,
reducing the overall system cost with the need for fewer output capacitors.
Output Voltage Setting
The PL1084 can be programmed to any voltages in the range of 1.25V to 5V with the addition of R1 and R2 external
resistors according to the following formula:
Vout=Vref(1+R2/R1)+Iadj*R2, where Vref=1.25V typically, Iadj=40μA typically
The PL1084 keeps a constant 1.25V between the output pin and the adjust pin. By placing a resistor R1 across these
two pins, a constant current flows through R1, adding to the Iadj current requirement of the PL1084. R1 is typically
selected to be 121Ω resistor so that it automatically satisfies the minimum current requirement. Notice that since
Iadj is typically in the range of 40μA, it only adds a small error to the output voltage and should only be considered
when a very precise output voltage setting is required. For example, in a typical 3.3V application where R1=121Ω
and R2=200Ω, the error due to Iadj is only 0.3% of the nominal set point.
Load Regulation
Since the PL1084 is only a 3 terminal device, it is not possible to provide true remote sensing of output voltage at the
load. The best load regulation is achieved when the bottom side of R2 is connected to the load and the top side of R1
is connected directly to the case or the Vout pin of the regulator and not to the load. It is important to note that for
high current applications, this can represent a significant percentage of the overall load regulation and one must keep
the path from the regulator to the load as short as possible to minimize this effect.
Stability
The PL1084 requires the use of an output capacitor as part of the frequency compensation in order to make the
regulator stable. The addition of 150μF aluminum electrolytic or a 22μF solid tantalum capacitor will ensure stability
for all operating conditions.
When the adjustment terminal is bypassed with a capacitor to improve the ripple rejection, the requirement for an
output capacitor increases. The value of 22μF tantalum or 150μF aluminum covers all cases of bypassing the
adjustment terminal. Without bypassing the adjustment terminal, smaller capacitor can be used with equally goo
result.
To ensure good transient response with heavy load current changes, capacitor values on the order of 100μF are used
in the output of many regulators. To further improve stability and transient response of these devices, larger values of
output capacitors can be used.
Thermal Design
The PL1084 incorporates an internal shutdown that protects the device when the junction temperature exceeds the
maximum allowable junction temperature. Although this device can operate with junction temperatures in the range
of 150, it is recommended that the selected heat sink be chosen such that during maximum continuous load
operation, the junction temperature is kept below the temperature.
Layout Consideration
The output capacitors must be located as close to the Vout terminal of the device as possible. It is recommended to
use a section of a layer of the PC board as a plane to connect the Vout pin to the output capacitors to prevent any high
frequency oscillation that may result due to excess trace inductance.
PL1084J3
CYStek Product Specification

4페이지










PL1084J3 전자부품, 판매, 대치품
Reel Dimension
Spec. No. : C512J3
CYStech Electronics Corp. Issued Date : 2007.07.04
Revised Date : 2014.12.29
Page No. : 7/9
Carrier Tape Dimension
PL1084J3
CYStek Product Specification

7페이지


구       성 총 9 페이지수
다운로드[ PL1084J3.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
PL1084J3

5A Low Dropout Positive Voltage Regulator

Cystech Electonics
Cystech Electonics

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵