|
|
PDF NXQ1TXA5 Data sheet ( Hoja de datos )
| Número de pieza | NXQ1TXA5 | |
| Descripción | One-chip 5V Qi wireless transmitter | |
| Fabricantes | NXP Semiconductors | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de NXQ1TXA5 (archivo pdf) en la parte inferior de esta página. Total 15 Páginas | ||
|
No Preview Available !
NXQ1TXA5
One-chip 5 V Qi wireless transmitter
Rev. 1.2 — 10 September 2015
Product short data sheet
1. General description
The NXQ1TXA5 is a controller/driver IC for a 5 V Qi-certified/compliant low-power
wireless charger. It offers a fully integrated solution that includes a 5 V full-bridge power)
stage, as defined in Wireless Power Consortium (WPC) 5 V Qi standards A5, A11, A12
and A16.
The NXQ1TXA5 uses dedicated analog ping circuitry to detect devices, according to the
Qi standard, achieving extremely low standby power consumption. If a Qi-compliant
receiver is detected, the NXQ1TXA5 starts to communicate with it. If the receiver is
recognized, it safely initiates wireless power transfer from the transmitter to the receiver,
while monitoring for fault conditions such as overheating or interference from metal
objects. The device is optimized to operate from a USB power supply and uses Smart
Power Limiting (SPL) to adjust the output power automatically to compensate for
power-limited supplies. The device supports Foreign Object Detection (FOD).
LED outputs and a buzzer output are available for the user interface. The LED outputs
feature a number of blinking modes. Static Power Reduction (SPR) allows multiple
NXQ1TXA5-based transmitters to operate from a single USB power supply by limiting
power consumption per device.
The NXQ1TXA5 is available in a 5 mm 5 mm, 32-pin HVQFN package.
2. Features and benefits
One-chip WPC 1.1.2 Qi-compliant device for A5/A11/A12/A16 5 V single-coil
low-power transmitter
Operates from 5 V supply
Integrated high-efficiency full-bridge power stage with low EMI radiation meeting
EN55022 radiated and conducted emission limits
Very few external components required, minimizing cost and board space
Extremely low-power receiver detection circuitry; standby power 10 mW (typical)
Power stage fully protected against overcurrents and overtemperature
Fully integrated accurate coil current measurement
Demodulates and decodes communication packages from Qi-compliant receivers
PID regulation for closed-loop power drive and control
Internal 1.8 V digital supply generation
LED (2) and buzzer outputs
NTC input for external temperature check and protection
On-chip thermal protection
Small HVQFN 32-pin package (5 5 mm) with 0.5 mm pitch
1 page  
NXP Semiconductors
NXQ1TXA5
One-chip 5 V Qi wireless transmitter
Table 4. Pin description[1] …continued
Symbol Pin Type Description
VDDP2 15, 16 P power supply pin 2
OUT2
17, 18 O transmitter output 2
GNDP[1]
19, 20, P
21, 22
power ground
OUT1
23, 24 O transmitter output 1
VDDP1 25, 26 P power supply pin 1
GNDD[1] 27 P digital ground
CDEC
28 P decoupling connection for internal LDO
XTAL_IN 29
I
crystal input
XTAL_OUT 30
O crystal output
TEST
31 I/O test pin; connect to ground
NFC_DIS 32
O NFC disable function
[1] For enhanced thermal and electrical performance, the exposed die-pad, and pins GNDP. GNDD must be
connected to top layer board ground. The exposed die-pad must also be connected to bottom layer board
ground with plated-through vias (see Section 12.4).
8. Functional description
8.1 Device operation
The NXQ1TXA5 is a 5 V wireless charger with an integrated full-bridge power stage. It
integrates all the functions required to control the power transfer between a
WPC-compliant Qi transmitter and a WPC-compliant Qi receiver efficiently. It can deliver
up to 8 W continuous power into the WPC-compliant Qi type A5, A11, A12 or A16
transmitter coil.
A block diagram of the NXQ1TXA5 is shown in Figure 1. It is operational when a 5 V
supply is connected and pin STBY is LOW. Internal 1.8 V biasing is activated and the
NXQ1TXA5 starts checking for a device on the transmitter base station. Power
consumption is extremely low (typically 10 mW) during this phase. When a device is
detected, the low-power DSP core starts up and sets up communications with the
detected device. Power transfer is initiated if the device is identified as a WPC-compliant
Qi receiver. The NXQ1TXA5 ensures that the correct power transfer level is maintained
with frequency and duty cycle control according to the WPC Qi specifications.
The power transfer can be monitored via the LED and BUZZER outputs. The external
temperature can be monitored via the NTC input to protect the application from
overheating when charging Qi-V1.0 receivers that do not support Foreign Object
Detection (FOD).
Additional inputs are provided to select the LED mode, configure FOD according to the
application design and coil/capacitor selection, set the SPR level and enable/disable SPL.
NXQ1TXA5_SDS
Product short data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 10 September 2015
© NXP Semiconductors N.V. 2015. All rights reserved.
5 of 15
5 Page 
NXP Semiconductors
NXQ1TXA5
One-chip 5 V Qi wireless transmitter
13. Package outline
+94)1 SODVWLFWKHUPDOHQKDQFHGYHU\WKLQTXDGIODWSDFNDJH QROHDGV
WHUPLQDOV ERG\[[PP
' %$
WHUPLQDO
LQGH[DUHD
$
( $
GHWDLO;
627
/
H
H
H E
Y &$%
Z&
H
\ &
&
\
(K H
H
WHUPLQDO
LQGH[DUHD
'K
;
'LPHQVLRQV
PP
VFDOH
8QLW $ $ E F ' 'K ( (K H H H / Y Z \ \
PD[
PP QRP
PLQ
1RWH
3ODVWLFRUPHWDOSURWUXVLRQVRIPPPD[LPXPSHUVLGHDUHQRWLQFOXGHG
2XWOLQH
YHUVLRQ
5HIHUHQFHV
,(&
-('(&
-(,7$
(XURSHDQ
SURMHFWLRQ
627
02
Fig 4. Package outline SOT617-3 (HVQFN32)
VRWBSR
,VVXHGDWH
NXQ1TXA5_SDS
Product short data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 10 September 2015
© NXP Semiconductors N.V. 2015. All rights reserved.
11 of 15
11 Page | ||
| Páginas | Total 15 Páginas | |
| PDF Descargar | [ Datasheet NXQ1TXA5.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| NXQ1TXA5 | One-chip 5V Qi wireless transmitter | NXP Semiconductors |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |