Datasheet.kr   

NX3L2G66 데이터시트 PDF




NXP Semiconductors에서 제조한 전자 부품 NX3L2G66은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


 

PDF 형식의 NX3L2G66 자료 제공

부품번호 NX3L2G66 기능
기능 Dual low-ohmic single-pole single-throw analog switch
제조업체 NXP Semiconductors
로고 NXP Semiconductors 로고


NX3L2G66 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 22 페이지수

미리보기를 사용할 수 없습니다

NX3L2G66 데이터시트, 핀배열, 회로
NX3L2G66
Dual low-ohmic single-pole single-throw analog switch
Rev. 8 — 7 February 2013
Product data sheet
1. General description
The NX3L2G66 is a dual low-ohmic single-pole single-throw analog switch. Each switch
has two input/output terminals (nY and nZ) and an active HIGH enable input (nE). When
pin nE is LOW, the analog switch is turned off.
Schmitt trigger action at the enable input (nE) makes the circuit tolerant to slower input
rise and fall times. The NX3L2G66 allows signals with amplitude up to VCC to be
transmitted from nY to nZ; or from nZ to nY. Its low ON resistance (0.5 ) and flatness
(0.13 ) ensures minimal attenuation and distortion of transmitted signals.
2. Features and benefits
Wide supply voltage range from 1.4 V to 4.3 V
Very low ON resistance (peak):
1.6 (typical) at VCC = 1.4 V
1.0 (typical) at VCC = 1.65 V
0.55 (typical) at VCC = 2.3 V
0.50 (typical) at VCC = 2.7 V
0.50 (typical) at VCC = 4.3 V
High noise immunity
ESD protection:
HBM JESD22-A114F Class 3A exceeds 7500 V
MM JESD22-A115-A exceeds 200 V
CDM AEC-Q100-011 revision B exceeds 1000 V
IEC61000-4-2 contact discharge exceeds 4000 V for switch ports
CMOS low-power consumption
Latch-up performance exceeds 100 mA per JESD 78 Class II Level A
Direct interface with TTL levels at 3.0 V
Control input accepts voltages above supply voltage
High current handling capability (350 mA continuous current under 3.3 V supply)
Specified from 40 C to +85 C and from 40 C to +125 C
3. Applications
Cell phone
PDA
Portable media player




NX3L2G66 pdf, 반도체, 판매, 대치품
NXP Semiconductors
NX3L2G66
Dual low-ohmic single-pole single-throw analog switch
7.2 Pin description
Table 3.
Symbol
1Y, 2Y
1Z, 2Z
GND
1E, 2E
VCC
Pin description
Pin
SOT833-1 and SOT996-2
1, 5
2, 6
4
7, 3
8
SOT902-2
7, 3
6, 2
4
1, 5
8
8. Functional description
Description
independent input or output
independent input or output
ground (0 V)
enable input (active HIGH)
supply voltage
Table 4. Function table[1]
Input nE
L
H
[1] H = HIGH voltage level; L = LOW voltage level.
9. Limiting values
Switch
OFF-state
ON-state
Table 5. Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
Symbol
Parameter
Conditions
Min Max Unit
VCC supply voltage
VI input voltage
enable input nE
VSW
switch voltage
IIK input clamping current VI < 0.5 V
ISK switch clamping current VI < 0.5 V or VI > VCC + 0.5 V
ISW switch current
VSW > 0.5 V or VSW < VCC + 0.5 V;
source or sink current
0.5
[1] 0.5
[2] 0.5
50
-
-
+4.6 V
+4.6 V
VCC + 0.5 V
- mA
50 mA
350
mA
VSW > 0.5 V or VSW < VCC + 0.5 V;
pulsed at 1 ms duration, < 10 % duty cycle;
peak current
-
500
mA
Tstg storage temperature
Ptot total power dissipation Tamb = 40 C to +125 C
65
[3] -
+150
250
C
mW
[1] The minimum input voltage rating may be exceeded if the input current rating is observed.
[2] The minimum and maximum switch voltage ratings may be exceeded if the switch clamping current rating is observed but may not
exceed 4.6 V.
[3] For XSON8 and XQFN8 packages: above 118 C the value of Ptot derates linearly with 7.8 mW/K.
NX3L2G66
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 7 February 2013
© NXP B.V. 2013. All rights reserved.
4 of 22

4페이지










NX3L2G66 전자부품, 판매, 대치품
NXP Semiconductors
NX3L2G66
Dual low-ohmic single-pole single-throw analog switch
Table 8. ON resistance …continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); for graphs see Figure 9 to Figure 15.
Symbol Parameter
Conditions
Tamb = 40 C to +85 Tamb = 40 C to Unit
C +125 C
Min Typ[1] Max
Min
Max
RON
ON resistance mismatch VI = GND to VCC;
between channels
ISW = 100 mA
[2]
VCC = 1.4 V
- 0.04 0.3
-
0.3
VCC = 1.65 V
- 0.04 0.2
-
0.3
VCC = 2.3 V
- 0.02 0.08
-
0.1
VCC = 2.7 V
- 0.02 0.075
-
0.1
RON(flat)
VCC = 4.3 V
ON resistance (flatness) VI = GND to VCC;
ISW = 100 mA
-
[3]
0.02 0.075
-
0.1
VCC = 1.4 V
- 1.0 3.3
-
3.6
VCC = 1.65 V
- 0.5 1.2
-
1.3
VCC = 2.3 V
- 0.15 0.3
-
0.35
VCC = 2.7 V
- 0.13 0.3
-
0.35
VCC = 4.3 V
- 0.2 0.4
-
0.45
[1] Typical values are measured at Tamb = 25 C.
[2] Measured at identical VCC, temperature and input voltage.
[3] Flatness is defined as the difference between the maximum and minimum value of ON resistance measured at identical VCC and
temperature.
NX3L2G66
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 7 February 2013
© NXP B.V. 2013. All rights reserved.
7 of 22

7페이지


구       성 총 22 페이지수
다운로드[ NX3L2G66.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
NX3L2G66

Dual low-ohmic single-pole single-throw analog switch

NXP Semiconductors
NXP Semiconductors

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵