Datasheet.kr   

BD8316GWL 데이터시트 PDF




ROHM Semiconductor에서 제조한 전자 부품 BD8316GWL은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


PDF 형식의 BD8316GWL 자료 제공

부품번호 BD8316GWL 기능
기능 Step-up and inverted 2-channel DC/DC converter
제조업체 ROHM Semiconductor
로고 ROHM Semiconductor 로고


BD8316GWL 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 23 페이지수

미리보기를 사용할 수 없습니다

BD8316GWL 데이터시트, 핀배열, 회로
Datasheet
Single-chip Type with Built-in FET Switching Regulator Series
Step-up and inverted
2-channel DC/DC converter
with Built-in Power MOSFET
BD8316GWL
Description
The BD8316GWL is step-up and inverted 2-channel
switching regulator with integrated internal high-side
MOSFET. With wide input range from 2.5~5.5V ,it
suitable for application of portable item. In addition,The
small package design is ideal for miniaturizing the
power supply.
Features
Wide input voltage range of 2.5V to 5.5 V
High frequency operation 1.6MHz
Incorporates Nch FET of 230mΩ/22V and Pch
Pow FET of 230mΩ/15V
Incorporates Soft Start (4.2msec(typ))and hight
side switch of boost channel
Independent ON/OFF signal(STB). Built-in
discharge SW for step up channel
Small package UCSP50L1( 1.8mm×1.5mm, 4×
3 grid, 11pin, WLCSP)
Circuits protection OCP,SCP,UVLO,TSD
Important Specifications
Input voltage range
2.55.5 [V]
Output boost voltage Input voltage(max)~18 [V]
Output inverted voltage
Maximum current
Operating frequency
Nch FET ON resistance
Pch FET ON resistance
Standby current
-9.0-1.0 [V]
1[A](max)
1.6 [MHz] (typ.)
230[mΩ]
230[mΩ]
1[μA](max)
Package
UCSP50L1 (WLCSP)
1.8mm×1.5mm×0.5mm, 4×3glid,11pin,
Application
LCD battery
CCD battery
Portable items that are represented by mobile phone
and DSC
Typical Application Input: 2.5 to 5.5 V, ch1 output: 5.6 V / 200m A, ch2 output:5.6V/200mA
0.1uF/10V
Vin→
2.5~5.5V
4.7uF/10V
EN CH1→
EN CH2→
VREF
VDD
STB1
STB2
GND
NON1
INV2
LX1
DIS1
HS2L
LX2
4.7uH
10kΩ
56kΩ
Vout1: -5.6V/200mA
4.7uF/10V
4.7uH
180kΩ
Vout2: 5.6V/200mA
4.7uF/10V
30kΩ
Fig.1 Application schematic
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
TSZ2211114001
1/20
TSZ02201-0Q1Q0AJ00170-1-2
2012.08.03 Rev. 003




BD8316GWL pdf, 반도체, 판매, 대치품
BD8316GWL
Datasheet
Function blacks description
1.Voltage Reference
This block generates ERROR AMP reference voltage.
The reference voltage of CH1 is 1.0V, The reference voltage of CH2 is 0.8V.
2.UVLO
Circuit for preventing malfunction at low voltage input.
This circuit prevents malfunction at the start of DC/DC converter and low input voltage .The function monitors VCC pin
voltage and if VCC voltage is lower than 2.2V, function turns off all output of FETs and DC/DC converter , and reset the
timer latch of the internal SCP circuit and soft-start circuit.
3.SCP
Short-circuit protection function based on timer latch system.
When the voltage of NON1 pin is higher than 0V or INV2 pin voltage is lower than 0.8V, the internal SCP circuit starts
counting.
SCP circuit detects output of Error AMP. Since internal Error AMP has highly gain as high as 80dB or more, if input
erroramp voltage cross reference voltage ,the output voltage of Error AMP goes high and detects SCP .
The internal counter is in synch with OSC, the latch circuit activates after the counter counts oscillations to turn off DC/DC
converter output (about 40.9 msec ).
To reset the latch circuit, turn off the STB pin once. Then, turn it on again or turn on the power supply voltage again.
4.OSC
This function determine oscillation frequency . Oscillation frequency of DC/DC converter set at 1.6MHz.
5.ERROR AMP
Error amplifier watch output voltage and output PWM control signals.
The internal reference voltage for Error AMP of ch1 is set at 0V.
The internal reference voltage for Error AMP of ch2 is set at 0.8V.
6.Timing Control
Voltage-pulse width converter for controlling output voltage corresponding to input voltage.
Comparing the internal SLOPE waveform with the ERROR AMP output voltage, PWM COMP controls the pulse width
and outputs to the driver.
Max Duties of ch1 and ch2 are set at 86%.
7.SOFT START
Circuit for preventing in-rush current at the start of DC/DC converter by bringing the output voltage.
Soft-start time is in synch with the internal OSC, and the output voltage of the DC/DC converter reaches the set voltage
after about 4.2m sec.
8.OCP
Circuit for preventing malfunction at over current.
Under input current over electrical characteristics , it supply minimum duty to DC/DC converter and IC stop safety by SCP
detected.
9.TSD
Circuit for preventing malfunction at high Temperature .
When it detects an abnormal temperature exceeding Maximum Junction Temperature (Tj=150), it turns OFF all Output
FET, and turns OFF DC/DC Comparator Output.
10. ON/OFF
Voltage applied on STB pin to control ON/OFF channel of each channel.
Turned ON when a voltage of 1.5 V or higher is applied and turned OFF when the terminal is open or 0 V is applied.
Incorporates approximately 800 kpull-down resistance.
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
TSZ2211114001
4/20
TSZ02201-0Q1Q0AJ00170-1-2
2012.08.03 Rev. 003

4페이지










BD8316GWL 전자부품, 판매, 대치품
BD8316GWL
Reference data
(unless otherwise specified Ta=25, VCC=3.6V)
1.030
1.020
1.010
1.000
VCC=2.5V VCC=3.6V
VCC=5.5V
0.990
0.980
0.970
-50
TEMPERATURE[℃]
0 50 100
Fig.4 VREF vs temp
150
Datasheet
0.850
0.840
0.830
0.820
0.810
0.800
0.790
0.780
VCC=2.5V
VCC=3.6V
0.770
VCC=5.5V
0.760
0.750
-50
TEMPERATURE[℃]
0 50 100
Fig.5 INV2 threshold vs temp
150
1.700
1.600
1.500
VCC=5.5V
VCC=3.6V
VCC=2.5V
1.400
1.300
0
24
VCC[V]
6
8
Fig.6 Oscillation frequency vs temp
2.400
2.300
2.200
2.100
Detect threshold
Reset threshold
2.000
-50
0 50 100
TEMPERATURE[℃]
150
Fig.7 UVLO detect threshold
Vs temp
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
TSZ2211114001
7/20
TSZ02201-0Q1Q0AJ00170-1-2
2012.08.03 Rev. 003

7페이지


구       성 총 23 페이지수
다운로드[ BD8316GWL.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
BD8316GWL

Step-up and inverted 2-channel DC/DC converter

ROHM Semiconductor
ROHM Semiconductor

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵