Datasheet.kr   

MADP-042305-13060 데이터시트 PDF




MA-COM에서 제조한 전자 부품 MADP-042305-13060은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.


 

PDF 형식의 MADP-042305-13060 자료 제공

부품번호 MADP-042305-13060 기능
기능 PIN Diodes
제조업체 MA-COM
로고 MA-COM 로고


MADP-042305-13060 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.




전체 4 페이지수

미리보기를 사용할 수 없습니다

MADP-042305-13060 데이터시트, 핀배열, 회로
MADP-042XX5-13060 Series
SURMOUNTTM PIN Diodes:
RoHS
Rev. V6
Features
 Surface Mount
 No Wirebonds Required
 Rugged Silicon-Glass Construction
 Silicon Nitride Passivation
 Polymer Scratch Protection
 Low Parasitic Capacitance and Inductance
 High Average and Peak Power Handling
 RoHS Compliant
Description
This device is a silicon, glass PIN diode surmount chip
fabricated with M/A-COM Tech’s patented HMICTM proc-
ess. This device features two silicon pedestals embedded
in a low loss, low dispersion glass. The diode is formed on
the top of one pedestal and connections to the backside of
the device are facilitated by making the pedestal sidewalls
electrically conductive. Selective backside metallization is
applied producing a surface mount device. This vertical
topology provides for exceptional heat transfer. The
topside is fully encapsulated with silicon nitride and has an
additional polymer layer for scratch and impact protection.
These protective coatings prevent damage to the junction
and the anode air-bridge during handling and assembly.
DE
G
F
Applications
These packageless devices are suitable for moderate
incident power applications, 10W/C.W. or where the
peak power is 50W, pulse width is 1μS, and duty cycle
is 0.01%. Their low parasitic inductance, 0.4 nH, and
excellent RC constant, make these devices a superior
choice for higher frequency switch elements when
compared to their plastic package counterparts.
Absolute Maximum Ratings1@ TAMB = +25°C
(unless otherwise specified)
Parameter
Absolute Maximum
MADP-042…-13060 305 405 505 905
C.W. Incident Power dBm 40 44 43 35
Forward Current
Reverse Voltage
Operating Temperature
250 mA
-80 V
-55°C to +125°C
Storage Temperature
Junction Temperature
-55°C to +150°C
+175°C
Mounting Temperature
+280°C for 10 seconds
DIM
A
B
C
D
E
F
G
INCHES
MIN
0.040
0.021
0.004
0.013
0.011
0.013
MAX
0.042
0.023
0.008
0.015
0.013
0.015
0.019
0.021
MM
MIN
1.025
0.525
0.102
0.325
0.275
0.325
MAX
1.075
0.575
0.203
0.375
0.325
0.375
0.475
0.525
Notes:
1. Backside metal: 0.1 μM thick.
2. Yellow hatched areas indicate backside ohmic gold contacts.
3. All devices have the same outline dimensions ( A to G).
1. Exceeding these limits may cause permanent damage.
1
ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions North America Tel: 800.366.2266 / Fax: 978.366.2266
is considering for development. Performance is based on target specifications, simulated results,
and/or prototype measurements. Commitment to develop is not guaranteed.
PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology
Solutions has under development. Performance is based on engineering tests. Specifications are
Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300
Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298
Visit www.macomtech.com for additional data sheets and product information.
typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available.
Commitment to produce in volume is not guaranteed.
M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make
changes to the product(s) or information contained herein without notice.




MADP-042305-13060 pdf, 반도체, 판매, 대치품
MADP-042XX5-13060 Series
SURMOUNTTM PIN Diodes:
RoHS
Rev. V6
Handling Procedures
All semiconductor chips should be handled with care to avoid damage or contamination from perspiration and skin oils. The
use of plastic tipped tweezers or vacuum pickups is strongly recommended for individual components. Bulk handling should
insure that abrasion and mechanical shock are minimized.
Bonding Techniques
Attachment to a circuit board is made simple through the use of surface mount technology. Mounting pads are conveniently
located on the bottom surface of these devices and are removed from the active junction locations. These devices are well
suited for solder attachment onto hard and soft substrates. The use of 80Au/20Sn, or RoHS compliant solders is
recommended. For applications where the average power is ~1W, conductive silver epoxy may also be used. Cure per
manufacturers recommended time and temperature. Typically 1 hour at 150°C.
When soldering these devices to a hard substrate, hot gas die bonding is preferred. A vacuum tip pick-up tool and a force of
60 to100 grams applied to the top surface of the device is recommended. When soldering to soft substrates, such as Duroid, it
is recommended to use a soft solder at the circuit board to mounting pad interface. Position the die so that its mounting pads
are aligned with the circuit board mounting pads. While applying a downward force perpendicular to the top surface of the die,
apply heat near the circuit trace and diode mounting pad. The solder connection to the two pads should not be made one at a
time as this will create unequal heat flow and thermal stress to the part. Solder reflow should not be performed by causing heat
to flow through the top surface of the die to the back. Since the HMIC glass is transparent, the edges of the mounting pads
can be visually inspected through the die after attachment is completed.
Typical re-flow profiles for Sn60/Pb40 and RoHS compliant solders is provided in Application Note M538 , “Surface Mounting
Instructions“ and can viewed on the MA-COM website @ www.macomtech.com
Ordering Information
The MADP-042XX5-13060 series of surmounts may be ordered in either gel packs or tape and reeled by adding the
appropriate suffix per the table below. Tape and reel dimensions are provided in Application Note M513 located on the
M/A-COM Tech’s website @ www.macomtech.com.
Gel Pack
MADP-042305-13060G
MADP-042405-13060G
MADP-042505-13060G
MADP-042905-13060G
Part Number
Tape and Reel
Surf Tape
MADP-042305-13060T
MADP-042405-13060T
MADP-042505-13060T
MADP-042905-13060T
Tape and Reel
Pocket Tape
MADP-042305-13060P
MADP-042405-13060P
MADP-042505-13060P
MADP-042905-13060P
4
ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions North America Tel: 800.366.2266 / Fax: 978.366.2266
is considering for development. Performance is based on target specifications, simulated results,
and/or prototype measurements. Commitment to develop is not guaranteed.
PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology
Solutions has under development. Performance is based on engineering tests. Specifications are
Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300
Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298
Visit www.macomtech.com for additional data sheets and product information.
typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available.
Commitment to produce in volume is not guaranteed.
M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make
changes to the product(s) or information contained herein without notice.

4페이지












구       성 총 4 페이지수
다운로드[ MADP-042305-13060.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는 부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.


구매 문의
일반 IC 문의 : 샘플 및 소량 구매
-----------------------------------------------------------------------

IGBT, TR 모듈, SCR 및 다이오드 모듈을 포함한
광범위한 전력 반도체를 판매합니다.

전력 반도체 전문업체

상호 : 아이지 인터내셔날

사이트 방문 :     [ 홈페이지 ]     [ 블로그 1 ]     [ 블로그 2 ]



관련 데이터시트

부품번호상세설명 및 기능제조사
MADP-042305-13060

PIN Diodes

MA-COM
MA-COM

DataSheet.kr       |      2020   |     연락처      |     링크모음      |      검색     |      사이트맵