LC863340B - (LC8633xxB) 8-Bit Single Chip Microcontroller

Sanyo Electric에서 제조한 전자 부품 LC863340B은 전자 산업 및 응용 분야에서
광범위하게 사용되는 반도체 소자입니다.

LC863340B의 기능 및 특징 중 하나는 "(LC8633xxB) 8-Bit Single Chip Microcontroller" 입니다.

PDF 형식의 LC863340B 자료 제공

LC863340B 기능

(LC8633xxB) 8-Bit Single Chip Microcontroller

Sanyo Electric

LC863340B 데이터시트 를 다운로드하여 반도체의 전기적 특성과 매개변수에 대해 알아보세요.

PDF 파일안의 텍스트 미리보기

CMOS IC LC863364B/56B/48B/40B/32B/28B/24B/20B/16B 8-Bit Single Chip Microcontroller Under Development LC863364B/56B/48B/40B/32B/28B/24B/20B/16B 8-bit Single Chip Microcontroller with on-chip 64K/56K/48K/40K/32K/28K/24K/20K/16K-byte ROM, on-chip 640/512-byte RAM and 352x9 bit OSD RAM Overview The LC863364/56/48/40/32/28/24/20/16B are 8-bit single chip microcontrollers with the following on-chip functional blocks: - CPU : Operable at a minimum bus cycle time of 0.424 µs - On-chip ROM capacity Program ROM : 64K/56K/48K/40K/32K/28K/24K/20K/16K bytes CGROM : 16K bytes - On-chip RAM capacity : 640/512 bytes - OSD RAM : 352 × 9 bits

Contents of page 4 out of 22 pages :

www.DataSheet4U.com LC863364B/56B/48B/40B/32B/28B/24B/20B/16B (12) ROM correction function Max 128 bytes / 2 addresses (13) Interrupts - 15 sources 9 vectored interrupts 1. External Interrupt INT0 2. External Interrupt INT1 3. External Interrupt INT2, Timer/counter T0L (Lower 8 bits) 4. External Interrupt INT3, base timer 5. Timer/counter T0H (Upper 8 bits) 6. Timer T1H,T1L 7. SIO0 8. Vertical synchronous signal interrupt ( VS ), horizontal line ( HS ), AD 9. IIC, Port 0 - Interrupt priority control Three interrupt priorities are supported (low, high and highest) and multi-level nesting is possible. Low or high priority can be assigned to the interrupts from 3 to 9 listed above. For the external interrupt INT0 and INT1, low or highest priority can be set. (14) Sub-routine stack level - A maximum of 128 levels (stack is built in the internal RAM) (15) Multiplication/division instruction - 16 bits × 8 bits (7 instruction cycle times) - 16 bits / 8 bits (7 instruction cycle times) (16) 3 oscillation circuits - Built-in RC oscillation circuit used for the system clock - Built-in VCO circuit used for the system clock and OSD - X’tal oscillation circuit used for base timer, system clock and PLL reference (17) Standby function - HALT mode The HALT mode is used to reduce the power dissipation. In this operation mode, the program execution is stopped. This mode can be released by the interrupt

PDF 파일 전체 : 22 페이지중 1, 2페이지 미리보기

[ LC863340B.PDF 데이터시트 ]

당사 플랫폼은 키워드, 제품 이름 또는

부품 번호를 사용하여 검색할 수 있는

포괄적인 데이터시트를 제공합니다.

부품번호	상세설명 및 기능	제조사
LC863340	8-Bit Single Chip Microcontroller	Sanyo Semicon Device
LC863340A	8-Bit Single Chip Microcontroller	Sanyo Semicon Device

LC863340B 데이터시트 PDF

PDF 형식의 LC863340B 자료 제공

PDF 파일안의 텍스트 미리보기

관련 데이터시트